How to Fix a Showerhead Leak

How to Repair a Showerhead

1. Remove the Showerhead

   Make sure the shower faucet handle is fully in the OFF position. By hand, turn the showerhead counter-clockwise off the threaded end of the shower arm.

   Tip

   If the showerhead is hard to turn, use a damp washcloth to grip it. Or you can use channel-lock pliers.

2. Inspect and Clean the Showerhead

   Inside the showerhead will be rubber O-rings and a screen, and perhaps other parts. Make sure that they are intact and not damaged or blocked with sediment. If the inside of the showerhead is dirty, clean your showerhead. Submerge the showerhead in a bowl of white vinegar for an hour or two. Rinse the parts off with cold water before reassembling them.

3. Wrap Pipe Threads

   Clean off the threads of the shower arm with a small nylon scrub brush. Wrap the threads with one or two loops of thread-sealing tape, sometimes sold as Teflon tape. Wrap the tape clockwise.

4. Reassemble the Showerhead

   Thread the showerhead back onto the shower arm and tighten it by hand. Turn on the shower faucet briefly to watch how the water stream performs.

   If the showerhead continues to dribble only when the faucet is ON, then you can consider replacing the entire showerhead—a simple matter of threading on a new showerhead rather than reattaching the old one.

How to Fix a Leaky Shower Cartridge

Most single-handle shower faucets work with a replaceable cartridge inside the faucet body, which has seals and rings that control the flow and mix of water up to the showerhead. If this cartridge does not seal properly, it will allow a slow trickle of water to continue upwards to the showerhead even when the faucet handle is in the OFF position.

1. Shut Off the Water

   Shut off the water upstream from the shower controls. Your home may have intermediary fixture shut-off valves located on the other side of the shower, often behind a wall panel. Some shower faucets have water shutoff valves built into the faucet body itself; you simply turn the valves with a screwdriver to shut off the flow of water from the hot and cold supply tubes into the faucet body. These shutoffs are visible once you remove the shower faucet's escutcheon plate.

   Many showers don't have any fixture shutoff valves. If this is the case, you will need to shut off the water at the main shut-off valve.

2. Remove the Faucet Handle

   The shower faucet handle will likely have a cap at the end that you can remove by gently prying it away with screwdriver or utility knife. With the cap off, unscrew the handle screw. In some cases, you may need to use a hex wrench to remove the handle screw.

3. Remove the Escutcheon Plate

   The faucet valve is usually covered by a large face place, or escutcheon. Remove the escutcheon by removing the mounting screws that hold it to the wall. You may need to cut through a caulk bead around the escutcheon in order to remove it.

4. Remove the Retaining Clip

   The faucet cartridge is usually held into place in the faucet body with a metal retaining clip. Carefully pry off this U-shaped retaining clip with a flat-head screwdriver. If there are washers present on the end of the cartridge, remove them.

   Ons some shower faucets, there is also a hex nut that needs to be removed in order to remove the cartridge.

   Tip

   Some manufacturers make special cartridge-puller tools that make it easier to remove their cartridges.

5. Slide Out the Cartridge

   Slide the existing cartridge out from the faucet body. Cartridges usually slide straight in and out, no turning or twisting required, but in some instances, you may need to grip the stem with channel-lock pliers and turn the cartridge to remove it.

6. Install a New Cartridge

   The new shower cartridge will slide straight into the faucet body if you align the tab on the cartridge with the groove on the faucet body. After inserting the cartridge, replace the retaining clip and hex screw, if present. Replace any washers you removed.

7. Replace the Escutcheon and Handle

   Reverse the earlier steps to replace the control handle and escutcheon plate. Turn on the water at the source. Test the shower by turning it on and then firmly off again several times, making sure the new cartridge controls the water flow correctly.

When to Call a Professional

Fixing the showerhead and replacing the shower cartridge fix the majority of showerhead leaks. If you have tried these two repairs and the showerhead still leaks, call a licensed plumber.