Next Article in Journal
Prediction of the Stability of Chemical Composition of Therapeutic Groundwater
Next Article in Special Issue
Removal of Pharmaceuticals from Water: Conventional and Alternative Treatments
Previous Article in Journal
Using OCO-2 Satellite Data for Investigating the Variability of Atmospheric CO2 Concentration in Relationship with Precipitation, Relative Humidity, and Vegetation over Oman
Previous Article in Special Issue
Acetaminophen Removal from Water by Microalgae and Effluent Toxicity Assessment by the Zebrafish Embryo Bioassay
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Review

Advanced Oxidation Processes for the Removal of Antibiotics from Water. An Overview

Department of Organic & Inorganic Chemistry, University of Extremadura, Avda de Elvas s/n, ES-06006 Badajoz, Spain
*
Author to whom correspondence should be addressed.
Water 2020, 12(1), 102; https://doi.org/10.3390/w12010102
Submission received: 31 July 2019 / Revised: 26 November 2019 / Accepted: 2 December 2019 / Published: 27 December 2019

Abstract

:
In this work, the application of advanced oxidation processes (AOPs) for the removal of antibiotics from water has been reviewed. The present concern about water has been exposed, and the main problems derived from the presence of emerging pollutants have been analyzed. Photolysis processes, ozone-based AOPs including ozonation, O3/UV, O3/H2O2, and O3/H2O2/UV, hydrogen peroxide-based methods (i.e., H2O2/UV, Fenton, Fenton-like, hetero-Fenton, and photo-Fenton), heterogeneous photocatalysis (TiO2/UV and TiO2/H2O2/UV systems), and sonochemical and electrooxidative AOPs have been reviewed. The main challenges and prospects of AOPs, as well as some recommendations for the improvement of AOPs aimed at the removal of antibiotics from wastewaters, are pointed out.

1. Introduction

Water is a natural resource, scarce, and indispensable for human life that also allows the sustainability of the environment. It is an essential part of any ecosystem, both qualitatively and quantitatively. However, water is unevenly distributed in different regions of the world, and its quality is not the same in all of them. For example, more than one-half of the world’s major rivers are severely depleted or polluted, so they degrade contaminating ecosystems and threaten the health of living beings. According to WHO and UNICEF data, 780 million people do not have access to drinking water, of which 185 million use surface water to meet their daily needs [1,2].
As noted in the second United Nations report on the development of water resources in the world [3], poor water quality slows down economic growth and can have adverse effects on health and livelihoods. Chemical contamination of surface waters, mainly due to industrial and agricultural discharges, is also a significant health risk in some developing countries. Pollution and industrial waste are endangering water resources, damaging and destroying the ecosystems of the entire world.
In recent decades, one of the biggest concerns in the environmental field is the risk associated with the pollution derived from persistent organic compounds (POPs). POPs are a group of chemical compounds that resist to a different extent the photochemical, chemical, and biochemical degradation, which causes their average life to be high in the environment. As a consequence, many POPs have been detected in low quantities (mg·L−1) in rivers, lakes, and oceans around the world, and even in drinking water [4]. Although the carcinogenic, mutagenic, and bactericidal properties of most POPs remain unknown, there is a great interest in their elimination from the waters to avoid their potential toxic consequences and the possible dangerous effects on the health of living organisms, including humans. Organic pollutants, not just POPs, are responsible for severe damages when they are accumulated in the environment [5].
For a long time, the scientific community has focused its efforts on the study of chemical pollutants that are regulated in different legislations. These include mostly apolar, toxic, persistent, and bioaccumulative pollutants, such as polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs), or dioxins. However, in recent years, the development of new and more sensitive methods of analysis has made it possible to detect the presence of other potentially dangerous contaminants, globally referred to as “emerging pollutants”. These are defined as previously unknown or unrecognized pollutants, not regulated by legislation, and whose effects on health and environment are not sufficiently known yet. They can be included in various sub-groups: Steroids and hormones, pharmaceutical and personal care products, antiseptics, surfactants, disinfection products, dyes, preservatives, etc. Their presence in the environment is not necessarily new, but concern about its possible consequences is arising since its impact on the different environments is unknown. However, due to their high production, consumption, and continuous introduction into the environment, they do not need to be persistent to cause adverse effects [6].
In the last few decades, advances in analytical methods have allowed the detection of very low concentrations (of the order of ng/L) of various compounds in waters that were not analyzed until now [7]. Even though these so-called emerging compounds are not always subjected to the existing regulations on water quality, their effects on human health and the environment make their elimination convenient [8]. The risk associated with the presence of these pollutants in the environment is not only due to their acute toxicity, but also to their genotoxicity, their capacity to develop resistance in pathogens, and the risk of endocrine alterations due to the continued exposure of aquatic organisms to these contaminants [9]. On the other hand, these products designed to be biologically active can significantly affect fishes and aquatic plants, even at very low concentrations [10]. The synergistic effect of some products on other pollutants is also known.
The degradation of the aquatic environment caused by these pollutants must be prevented [11], and control is particularly challenging due to the wide dispersion of their emission sources ranging from domestic or industrial waste to landfills. Very frequently, due to the demands of their design, they are relatively non-biodegradable compounds. For this reason, the conventional treatment of active sludge, widely used in urban wastewater treatment plants, is insufficient for the elimination of these compounds [12,13].
Therefore, it is necessary to use other technologies for the elimination of these compounds. Within these technologies, advanced oxidation processes (AOPs) have a high application potential, mainly derived from the high reactivity and low selectivity of the hydroxyl radicals. However, the presence of natural organic matter and low concentration of these micropollutants are factors to consider when applying these treatments since ·OH radicals oxidize both substrates. Furthermore, the high reaction rate of these radicals with the micropollutants does not necessarily imply greater process efficiency [14].
Among all types of pollutants, a group of recalcitrant compounds is formed by antibiotics (ABs), which are discharged into the aquatic environment in large quantities from industrial activities or excreted by humans or animals. The accumulation of ABs in the environment constitutes a risk for the aquatic flora and fauna and may cause resistance in some bacterial strains. These compounds are tough to degrade, mainly because they tend to have a very complex structure that makes them quite stable and, consequently, poorly biodegradable [15,16]. Hence, the removal of antibiotics from aqueous medium constitutes one of the most significant challenges in the field of water treatment. A wide variety of conventional treatments have been developed to remove pollutants from waters.
These conventional treatments can be classified into three broad groups, namely physical, chemical, and biological treatments. Table 1 summarizes the advantages and disadvantages of these traditional treatments.
This conventional approach, hence, makes combined use of physical, chemical, and biological treatments, with the main goal of removing sediments and organic matter that could promote both, the growth of microorganisms, and the eutrophication of water bodies. Moreover, the use of conventional methods is not wholly accepted nowadays because of the high costs and operational problems [17,18]. Also, they are not very efficient for the treatment of persistent or emerging pollutants in water, such as antibiotics, since many of these compounds have complex structures and, therefore, exhibit high chemical stability that hinders their complete degradation. The generation of harmful wastes in these processes is also a significant disadvantage. Consequently, it is necessary to adopt more modern systems such as advanced oxidation processes (AOPs).
The implementation of cleaner production programs framed in the reduction of discharges and polluting effluents, and especially the application of environmentally sustainable technologies in industrial processes, is of the utmost importance nowadays. That is why the use of AOPs technologies is currently under development. AOPs were defined by Glaze et al. [19] as water treatment processes performed at pressure and temperature close to environmental conditions, which involve the generation of hydroxyl radicals in sufficient quantity to interact with the organic compounds of the medium. Wastewater treatment plants (WWTPs) generally do not reach the complete elimination of many contaminants. Therefore, they behave as an important source of release of some polluting products into the environment. The implementation of sustainable technologies is imposed as a possible solution for the recovery of high-quality treated effluent. AOPs are new water purification technologies that have been widely used in the last years due to their versatility and a broad spectrum of applicability [20] and constitute a group of very efficient methods for water and wastewater treatment [21,22,23].
AOPs include all the catalytic and non-catalytic processes that take advantage of the high oxidizing capacity of the hydroxyl radical (OH), and they differ from each other in the way in which this radical is generated. These processes are mainly based on the “in situ” generation of the hydroxyl radical that reacts rapidly with most organic compounds, except chlorinated alkanes [24]. Thus, such radical is generated in sufficient quantity to interact with organic compounds [4,25]. AOPs can be classified into two broad groups: Homogeneous processes and heterogeneous processes, distinguishing between those that operate with an external input of energy (radiant energy, ultrasonic energy, electrical energy) and those that do not.
Hydroxyl radicals are optimal within the group of powerful oxidants because they meet a series of requirements:
  • They do not generate additional waste.
  • They are not toxic and have a very short lifetime
  • They are not corrosive to pieces of equipment.
  • They are usually produced by assemblies that are simple to manipulate.
According to these considerations, AOPs are technologies compatible with the environment and based on them, competitive processes from an economic point of view are being developed. The viability of the AOPs depends on the efficacy of the OH radical, which is the second known species with higher oxidant power after fluorine [4,26] (Table 2).
The ·OH radical acts in a non-selective manner on organic and organometallic contaminants in the aqueous medium, ideally leading to their complete mineralization to CO2, water, and inorganic ions [27,28,29,30,31].
The ·OH radical is a highly reactive species, and therefore does not accumulate in the medium but can react efficiently with organic pollutants that are refractory to the action of other oxidants, giving rise to rate constants in the order of 106–1010 M−1 s−1 [32,33]. The most important advantage of the advanced oxidation processes is that they are respectful of the environment [34].
Hydroxyl radicals can degrade organic or organometallic compounds by three degradation mechanisms, depending on the nature of the compound:
  • Dehydrogenation or abstraction of a hydrogen atom to form water (if the substrate has C-H bonds, e.g., alkanes) and radical R· that in the presence of molecular oxygen can generate the peroxyl radical ROO· and thus initiate an oxidative sequence that can lead to mineralization, Reactions (1) and (2).
    RH + OH → H2O + R
    R + O2 → ROO
  • Hydroxylation of the organic compound by the attack of·OH in the high electron density sites, adding to the unsaturated bonds of aromatic or aliphatic compounds and initiating a chain of oxidation reactions, Reactions (3)–(6).
    ROO·+ n(·OH/O2) → xCO2 + yH2O
    ArH + OH → ArH(OH)
    ArH(OH) + O2 → [ArH(OH)OO]
    [ArH(OH)OO] → ArH(OH) + HO2
  • Charge transfer by oxidation-reduction, causing the ionization of the molecule, Reaction (7).
    OH + RX → RX·+ OH
The radical mechanisms are complicated so that the oxidation of organic matter by OH radicals involves several types of species and reactions:
  • Initiation reactions during which radical species R· are formed, Reaction (1).
    RH + OH → H2O + R
  • Propagation reactions involving radical species R· that react with other neutral organic molecules, Reaction (8), or with dissolved oxygen in the solution, Reaction (2).
    R·+ R’H → RH + R’·
    R + O2 → ROO
  • Termination reactions where the radicals combine, Reactions (9)–(11).
    R·+ R·→ R-R
    R·+ OH → R-OH
    OH + OH → H2O2
Many AOPs are based on the combination of a strong oxidizing agent (e.g., ozone or hydrogen peroxide) with a catalyst (e.g., transition metal ions or photocatalysts) and/or radiation (e.g., UV or ultrasound).
One of the possible classifications of the AOPs is based on the source of generation of the oxidizing species; that is, the method to generate the hydroxyl radicals. This classification is shown in Table 3, which lists the main types of AOPs: photolytic, based on the use of ozone, based on the use of hydrogen peroxide, photocatalytic, electrochemical, or by ultrasound. The wide variety of available techniques evidences the versatility of AOPs.
In short, the most positive characteristics of the AOPs can be summarized as follows:
  • Potential capacity to carry out mineralization of organic pollutants to carbon dioxide and water, and oxidation of inorganic compounds and ions such as chlorides, nitrates, etc.
  • Non-selective reactivity with the vast majority of organic compounds, especially attractive to avoid the presence of potentially toxic byproducts from the primary pollutants that can be originated by other methods that do not achieve complete oxidation.
The main disadvantage of AOPs lies in their high cost due to the use of expensive reagents (for example, H2O2) and energy consumption (generation of O3 or UV radiation). Therefore, the future prospects of these processes include a renewed technology combined with adequate use of kinetic-chemical models.
In the following sections, a bibliographic review dealing with the most important contributions to each of the AOPs summarized in Table 3 is presented. Most of the works referred to have been published in the last decade, although references to papers published in the first decade of the 21st Century have been included, too. On the contrary, references to works published in the 1970s, 1980s, and 1990s have been reduced to a minimum. This paper follows the path of some previously published reviews dealing with the removal of antibiotics in water by AOPs [35,36,37,38,39,40,41,42,43,44,45,46,47].
In this review, after some preliminary considerations concerning the scarcity and necessity of water worldwide, the concerns on water pollution by persistent pollutants, and the main drawbacks of the use of conventional methods to remove them, an update is presented on the novel approaches for wastewater remediation based on advanced oxidation processes. The main challenges and future prospects of AOPs, as well as some recommendations for the improvement of AOPs aimed at the removal of antibiotics from wastewaters, have been dealt with in the final sections of this work.

2. Photolysis

Photolytic methods for the degradation of pollutants dissolved in water are based on providing energy to chemical compounds in the form of radiation, which is absorbed by different molecules to reach excited states for the time necessary to undergo different chemical reactions. Molecules absorb radiant energy in the form of quantized units called photons, which provides the energy required to excite specific electrons and form free radicals that undergo a series of chain reactions to give the reaction products. These free radicals can be generated by homolysis of weak bonds, or by electronic transfer from the excited state of the organic molecule to molecular oxygen, resulting in the superoxide radical (O2·), or other chemical reagents such as ozone or hydrogen peroxide (reactions that will be discussed later) so that hydroxyl radicals are produced. These photolytic methods use UV radiation due to the higher energy of their photons as indicated by the Planck’s equation:
Eλ = hc/λ  ec.
where Eλ is the energy of a photon associated with the wavelength (λ) of the radiation; h is the Planck’s constant; and c is the speed of light.
Thus, direct photolysis involves the interaction of light with molecules to cause their dissociation into simpler fragments. For this reason, in any process in which UV radiation is used, photolysis could take place. The intensity and wavelength of the radiation or the quantum yield of the compound to be eliminated are factors that influence the performance of the process. As a source of UV radiation, mercury vapor lamps are usually used [48].
Indirect photodegradation is due to oxidation mediated by radicals that are generated when light excites some molecules, commonly known as photosensitizers. Dissolved organic matter—particularly humic and fulvic acids—and nitrate ions are two examples of photosensitizers usually found in aquatic environments. It is worth noting that the generation of radicals by sensitizers is a UV light-mediated process and, hence, indirect photodegradation takes place to the detriment of direct photolysis.
The data summarized in Table 4 illustrate the mechanisms and removal efficiencies of the different photolytic processes aimed at abating a wide variety of antibiotics in aqueous solution.
It is widely accepted that direct photolysis is a fast process. However, pollutants are removed by direct photolysis to a limited extent. Photosensitizers-mediated processes contribute to improving removal efficiencies.
Among the main advantages of this group of AOPs, it is worth noting that photolysis is a chemical-free treatment that requires relatively low maintenance and operational costs. Moreover, UV has proven its versatility and capacity to promote the cleavage of the chemical bonding of a wide variety of refractory compounds. Hence, the use of UV irradiation in AOPs aimed at the treatment of wastewater is rising in the last years.
However, the use of UV-alone treatments has some crucial limitations. For instance, the occurrence of organic molecules suitable to behave as photosensitizers may also cause an increase in the turbidity of the aqueous media, thus hindering the penetration of UV radiation in the polluted medium. This latter hinders the contribution of indirect photolysis so that the process becomes less efficient.
It should be noted, however, that ultraviolet radiation alone is not usually applied as an advanced oxidation process (AOP). The use of UV irradiation, together with other oxidants, may contribute to the degradation of the parental pollutants as well as that of potentially harmful byproducts [60,61]. Furthermore, most of the low-pressure UV lamps that are commercially available emit approximately 5% of the radiation of a wavelength close to 185 nm, which produces ozone in the reactor. Hence, UV has been widely used combined with oxidizing agents such as ozone or hydrogen peroxide to enhance the generation of hydroxyl radicals, as will be exposed in the next sections of this work.
In general, direct photolysis is less effective in the degradation of pharmaceuticals present in wastewaters and also requires more energy than, for example, ozonation [62]. Hence, in the next section, advanced oxidation processes based on the use of ozone are presented.

3. Ozone-Based AOPs

Ozone is a powerful oxidizing agent capable of reacting with a large number of organic and inorganic compounds. Its high oxidation potential (E° = 2.08 V, see Table 2) and the absence of the formation of dangerous byproducts during the process have increased the importance of this technique in water treatment during the past decades. The main drawback is the need to generate ozone from oxygen, for which an electric discharge over a stream of air or pure oxygen is used. This step consumes large amounts of energy, thus handicapping the scaling of the process.

3.1. Ozonation

The mechanism of oxidation by ozone is a complex process that takes place in two ways: Direct reaction with dissolved ozone (O3) or indirect oxidation through the formation of radicals (·OH). The extension of both mechanisms throughout the degradation of a compound depends on factors such as the nature of the contaminant, the dose of ozone, or the pH of the medium. Normally, under acidic conditions (pH < 4) direct ozonation prevails, Reaction (12):
3O3 + OH + H+ → 2 OH + 4O2
On the contrary, at pH > 9, the indirect route is the most important one. As a rule, degradation rates in ozonation processes increases as pH does, since high pH favors ozone decomposition into free radicals as shown in Reaction (13). Other chemical reactions involved in the indirect oxidation with ozone are as follows:
O3 + OH → O2 + HO2
O3 + HO2 → HO2 + O3
HO2 → H+ + O2
O2 + O3 → O2 + O3
O3 + H+ → HO3
HO3 → HO·+ O2
Under alkaline conditions, however, a fast side-reaction must be taken into account:
HO + O3 → HO2·+ O2
This latter reaction results in a rapid generation of hydroperoxyl radicals (E° = 1.65V) to the detriment of the ·OH radicals (E° = 2.80 V) and leads to a decrease in the oxidation ability.
Table 5 lists some selected papers dealing with conventional ozonation treatments of a wide variety of antibiotics, indicating the aqueous matrix and the main experimental conditions.
If O3 mediated oxidation is performed under acidic or near-neutral pH, the degradation of the pollutants mainly takes place through direct reactions between O3 and the organic molecules. The main targets of ozone attack are -C = C- or -N = N- double bonds.
Several operational parameters strongly influence the formation of O3 and its subsequent transformation into ·OH radicals. Among these parameters, the chemical structure and concentration of the pollutant, the quality of the effluent, pH (as indicated above), and temperature must be taken into consideration. The main advantages of ozonation are:
(i)
The volume of effluent remains constant along the process and sludge is not formed,
(ii)
Installations are relatively simple and require only a little space,
(iii)
O3 is generated in situ, so that no stock solutions of H2O2, iron salts, or other chemicals are needed on-site,
(iv)
It can be applied even if the effluent fluctuates both in terms of flow rate and/or composition and
(v)
O3 remnants can be eliminated as ozone tends to decompose into oxygen.
As indicated above, the main inconvenience is the relatively high cost of equipment and maintenance, together with the high requirements of energy that must be supplied to carry on the process.
Another key point to be taken into consideration is the necessity to ensure an adequate mass transfer. It must be born in one’s mind that O3 molecules must be transferred from the gas phase to the liquid phase so that the attack on the chemical bonds of the organic molecules may occur. Very frequently, the mass transfer may be regarded as the limiting step of the process. An inadequate mass transfer can negatively affect the removal efficiency of the process and, hence, result in increasing the operating costs. An adequate reactor design helps to avoid this critical drawback of ozonation, as will be discussed later.
Furthermore, if high levels of bromide ions are present in the effluent, ozonation can lead to the generation of bromate, which has been proved to act as a carcinogen [80].
The ozonation treatment can be improved by coupling with hydrogen peroxide and/or UV (O3/UV, O3/H2O2, or O3/H2O2/UV processes). The next sections are devoted to these binary or ternary systems.

3.2. The O3/UV System

Ozonation alone poses several advantages over conventional chemical oxidants such as chlorine or chlorine dioxide; however, it does not generate enough concentration of hydroxyl radicals to degrade organic compounds until total mineralization. This latter is due to the low value of the kinetic constant of the direct ozone-pollutant reaction. Hence, the concentration of hydroxyl radicals generated by decomposition of the ozone is insufficient, unless the pH of the medium rises, which would imply the use of external chemical agents. In short, higher concentrations of these radicals are required for the reduction of the pollutants.
The O3/UV combination generates large concentrations of hydroxyl radicals in a fast manner so that this technique is adequate for this type of mineralization processes. Therefore, ozonation in the presence of UV irradiation has become one of the most used AOPs for the degradation of organic compounds in general as acids, alcohols, and organochlorines of low molecular weight (dihalomethanes, trihalomethanes, etc.). Another essential advantage of the combined use of UV and O3 is the fact that the generation of bromate is inhibited.
The molar extinction coefficient of O3 is 3300 M−1·cm−1. Ozone strongly absorbs UV light of wavelength λ = 254 nm. To explain the generation of hydroxyl radicals from O3, a two-stage process has been proposed. In the first stage, the photoinduced homolysis of the ozone molecule takes place, Reaction (20), and in the second stage, the production of hydroxyl radicals as a consequence of the reaction of atomic oxygen O (1D) with water, Reaction (21), takes place [81]:
O3 + h → O2 + O(1D)
O(1D) + H2O → 2HO
However, the hydroxyl radicals recombine generating hydrogen peroxide; therefore, the photolysis of ozone in solution can be represented by Reaction (22).
O3+ H2O → [2·OH] + O2→ H2O2 + O2
The H2O2 molecules generated in this latter reaction may undergo different chemical reactions in the presence of ozone as follows [82]:
H2O2 → HO2 + H+
HO2 + O3 → HO2·+ O3
HO2·→ O2·+ H+
O2·+ O3 → O2 + O3
O3·+ H+ → HO3
HO3·→ HO·+ O2
Next,
RH + OH → H2O + R
R·+ O2 → ROO
Peyton and Glaze [81] suggest that initiation may occur either by the reaction of ozone with the HO or HOO species or by the photolysis of hydrogen peroxide. The reaction with water of the radical anion ozonate, O3·is rapid, Reaction (29). The spontaneous decomposition of the ozonate has also been proposed [83], Reaction (30).
O·+ H2O ⟶ OH + HO
O3·⟶O2 + O
Hence, as described in Reaction (1), the hydroxyl radicals react with the organic substances, and the kinetics of the process is speeded up by the presence of UV radiation. Of course, as indicated in the previous section, UV light itself can degrade some compounds by direct photolysis. Moreover, UV radiation can excite the organic molecules of the pollutant, increasing their susceptibility towards an attack by the hydroxyl radicals.
Nevertheless, since both UV and ozone are quite expensive to generate and need the consumption of large amounts of electric energy, there are relatively few works in the literature devoted to the study of the removal of pollutants by O3/UV processes in comparison with other UV- or ozone-based systems. Table 6 summarizes some research works dealing with the removal of several antibiotics by the O3/UV process.
The literature review suggests that the use of UV light combined with O3 increases the removal efficiency of refractory pollutants. This fact is attributable to the photolysis-mediated generation of larger amounts of ·OH radicals. However, the economic viability of this method is limited because of the remarkable energy requirement for the production of O3 and UV light.

3.3. The O3/H2O2 System

The direct action of ozone on certain typical water pollutants is advantageous, as discussed above, due to its ability to degrade high molecular weight electron-rich organic compounds. However, the decomposition of these large molecules usually gives rise to the generation of low molecular weight byproducts that may be refractory or recalcitrant towards both further ozone oxidation or degradation through ·OH radical-mediated pathways. Hence, it is possible that though the primary pollutants are entirely degraded by single ozonation, the degree of mineralization can be deficient [77]. This is, perhaps, the most critical disadvantage of the use of single ozonation as an AOP, since these low molecular weight byproducts may exhibit more acute toxicity than the primary pollutants. The concomitant use of hydrogen peroxide in ozonation may help to improve the process efficiency, since the reaction of O3 with H2O2 results in the generation of ·OH radicals. The O3/H2O2 combined oxidation system (commonly known as “peroxone”) produces higher conversion yields than ozonation in those cases in which the direct ozone-pollutant reaction follows a slow kinetic regime due to gas–liquid matter transfer problems. Under these circumstances, an advanced oxidation process such as the one that can be achieved by adding a small amount of hydrogen peroxide to the aqueous solution through which ozone is being bubbled is convenient [90].
Hydrogen peroxide in aqueous solution is partially dissociated into its conjugate base, the hydroperoxide ion (HO2), according to Reaction (23). Hydroperoxide ions react with ozone causing its decomposition, Reaction (24), and giving rise to a series of chain reactions in which the hydroxyl radical is involved [32]. Such reactions are much the same as indicated above as Reactions (25)–(28). Furthermore, ozone can react with hydroxyl radicals, Reaction (31), giving rise to more hydroperoxide ions that can further react with ozone, thus making the process continue. This way, the pollutant dissolved in water is susceptible to undergo oxidation through two simultaneous routes: The direct route (molecular reaction with ozone) or the indirect radical pathway (reaction with the hydroxyl radical).
H2O2 → HO2 + H+
HO2 + O3 → HO2·+ O3
HO2·→ H+ + O2
O2·+ O3→ O2 + O3
O3·+ H+→ HO3
HO3·→ HO·+ O2
HO·+ O3 → HO2·+ O2
Additionally, ozone may also react directly with hydrogen peroxide and more hydroxyl and ozonate radicals are generated:
2 H2O2 + O3 → 2 HO·+ O3
Some selected results obtained in the O3/H2O2 process are listed in Table 7.
Researchers agree that the O3/H2O2 system is highly effective in achieving fast and complete mineralization of recalcitrant organic pollutants that can be found in wastewaters. The addition of H2O2 accelerates O3 decomposition and the subsequent formation of ·OH radicals. This, in turn, makes the overall process faster since the reaction rate constant of the hydroxyl radical (i.e., 106–109 M−1 s−1) is several orders of magnitude higher than that of O3.

3.4. The O3/H2O2/UV System

In the H2O2/O3/UV system, there is a wide variety of individual processes that can give rise to the generation of ·OH radicals. Hence, this ternary system can be considered as the result of the integration of different unitary or binary systems, namely:
(a)
Direct photolysis.
(b)
Ozonation alone.
(c)
UV photolysis of O3.
(d)
The combined effect of O3 and H2O2.
(e)
UV photolysis of H2O2.
The methods (a) to (d) have been considered in previous sections of this work, whereas the UV photolysis of hydrogen peroxide will be dealt with in depth in Section 4.1.
All these processes result in the formation of ·OH radicals through a sequence of reactions that directly or indirectly are related to the formation of (and/or the reaction with) H2O2 as suggested by reactions
     Hν
O3 + H2O → [2·OH] + O2→ H2O2 + O2
2 H2O2 + O → 2 HO + O3
among others.
The main advantage of the ternary O3/H2O2/UV system lies in the fact that the decomposition of ozone is speeded up by the simultaneous presence of hydrogen peroxide and UV irradiation, thus yielding an increased rate of generation of ·OH radicals. Furthermore, it can also be applied under mild conditions (namely, atmospheric pressure and room temperature). However, the high costs of the three elements that constitute the system (i.e., ozone, hydrogen peroxide, and UV light) pose a remarkable disadvantage that limits a broader use of this process. Consequently, the use of this ternary system is usually restricted to the treatment of highly polluted effluents to achieve adequate degradation and mineralization of recalcitrant pollutants.
Some examples of the use of the O3/H2O2/UV system in the removal of antibiotics are summarized in Table 8.

4. Hydrogen Peroxide-Based AOPs

Hydrogen peroxide is a safe, abundant, and easy to use chemical reagent, widely used for the prevention of contamination. However, H2O2 itself does not exhibit good oxidizing properties and must be combined with other substances or catalysts to become more effective. The combined use of H2O2 with ozone has been described under Section 3.2. Hydrogen peroxide can be used in combination with the UV radiation but has also been widely applied together with Fe2+ and/or Fe3+ ions giving rise to the well-known Fenton and Fenton-like processes. Finally, a ternary combination of UV irradiation, H2O2, and Fe2+/Fe3+ ions, commonly known as the “Photo-Fenton process,” has been broadly reported in the literature. In the next sections, these processes will be described in some detail.

4.1. The H2O2/UV System

Ultraviolet radiation has been widely used for the treatment of water and wastewater around the world and has more and more applications in this field. Numerous studies show that this treatment is useful for the elimination of pharmaceuticals found in different types of surface water [59,98,99]. However, this technology is only applicable to waters containing photosensitive compounds and with low levels of COD (for example, river and drinking water) [41]. On the other hand, effluents from sewage treatment plants may contain high concentrations of organic compounds that can inhibit the process [100]. In these cases, UV/H2O2 is a particularly attractive alternative for the removal of organic molecules that exhibit low reactivity towards ozone and hydroxyl radicals, but that are markedly photoactive.
The UV/H2O2 system takes advantage of the joint action of two chemical processes, namely
(a)
The UV photolytic ability (regardless it is direct or indirect),
(b)
The reaction of the dissolved pollutants with the ·OH radicals generated in the homolytic cleavage of the O-O bond in H2O2.
It can be stated that the photolysis of an organic compound in aqueous solution catalyzed by the presence of hydrogen peroxide is a very complex process. The success of the H2O2/UV system lies in the stoichiometric formation of hydroxyl radicals (·OH) from the photocatalytic decomposition of H2O2 in the first stage of the photolytic degradation [101]:
  Hν
H2O2 → 2 OH
The quantum yield of this process is very high, forming a maximum of two hydroxyl radicals as absorbed, and invariable with the applied wavelength [102].
Next, a series of radical reactions takes place:
H2O2 + OH → HO2·+ H2O
H2O2 + HO2·→ OH + O2 + H2O
2 HO2·→ H2O2 + O2
OH + HO2·→ H2O2 + O2
From Reactions (34)–(37) it becomes evident that although the photolytic cleavage of hydrogen peroxide gives rise to the formation of ·OH radicals (Reaction (33)), the occurrence of high concentrations of H2O2 may have a scavenging effect on the hydroxyl radicals and, hence, may hinder the effectiveness of the oxidation process. Consequently, the H2O2 initial concentration must be carefully adjusted to maximize the efficiency of the removal process. Moreover, H2O2 is an expensive reagent that increases the total operating costs of the process [103].
Once the highly reactive ·OH radicals are formed, they react with the organic compound by different mechanisms: Abstraction of a hydrogen atom, addition to C=C double bonds, or electron transfer, depending on the nature and functional groups of the molecule. The most general reaction route is the abstraction of a hydrogen atom and the generation of the resulting organic radical R·, which in turn reacts rapidly with dissolved O2 to form the peroxide organic radical RO2· [21]. These organic radicals decompose by bimolecular reactions giving rise to the different degradation products of the starting compound together with other byproducts such as hydrogen peroxide, hydroperoxide radicals, formaldehyde, etc.
Finally, the dimerization reactions of the hydroxyl radicals themselves, i.e., the reverse process of Reaction (33) [104] and the hydroperoxide radicals, Reaction (36) [105], lead to the regeneration of hydrogen peroxide, which in turn can sequester hydroxyl radicals and re-form hydroperoxide radicals, Reaction (34) [106].
At the same time, one must consider the dissociation equilibria of the organic compound itself and of the different intermediates formed, such as hydrogen peroxide, hydroperoxide radicals, etc., which are shown below:
RH ↔ R + H+
H2O2 → HO2 + H+
HO2·→ H+ + O2
In summary, a cycle of decomposition and simultaneous formation of hydrogen peroxide can be established. The overall result of such a cycle will depend on several variables as, for instance, the intensity of the ultraviolet radiation, temperature, pH, and the nature of the organic compounds.
It must be noted, however, that the H2O2/UV system is considered one of the most viable advanced oxidation processes. For instance, on many occasions, it is preferable to ozonation because it is less sensitive to the nature and concentration of the polluting species.
Table 9 summarizes some examples of removal processes of antibiotics by the H2O2/UV process.
From the literature review, it may be concluded that the UV/H2O2 is a fast and efficient technology for the removal of antibiotics from aqueous matrices, due to a fast generation of OH radicals in solution. However, the overall performance of the process is remarkably dependent on different operational parameters such as the UV wavelength and intensity (i.e., the UV light source) and the inherent properties of the wastewater (i.e., pH, initial concentration of pollutants, etc.).

4.2. The Fe2+/H2O2 System. Fenton Reagent

The Fenton process is a viable alternative for the removal of organic pollutants from wastewater and has been applied in many industrial sectors. However, it has some disadvantages derived from the use of iron salts as a catalyst for the decomposition of hydrogen peroxide to hydroxyl radicals.
On the one hand, large amounts of these dissolved iron salts are necessary, which makes the process more expensive. On the other hand, the directives of the European Union on water quality allow a very low concentration of iron dissolved in the effluents, which forces to introduce some treatment aimed at eliminating iron salts from the effluents of the Fenton process. These complementary processes, typically physical–chemical coagulation–flocculation processes, produce large quantities of metal sludge as a waste, which must be managed appropriately too. These drawbacks of the conventional Fenton process have promoted the development of new systems, which allow minimizing the presence of iron species dissolved in the environment, without critically affecting the efficiency of the process.
Different alternatives can be distinguished to achieve this objective [116]. Firstly, technological options have been proposed to accelerate the regeneration of Fe(II) species, which is mainly responsible for the decomposition of hydrogen peroxide and the generation of hydroxyl radicals. This would reduce the amount of iron (II) needed in the reaction medium. One of these alternatives is the combined use of the Fenton process together with near-visible ultraviolet radiation, which constitutes the so-called “photo-Fenton process.” This process will be dealt with in detail in Section 4.4. Secondly, the development of solid catalysts for Fenton processes has attracted the attention of the scientific community in recent years. The use of highly active and stable solid catalysts would help to minimize the presence of iron (II) salts dissolved in the medium, besides facilitating the recovery and reuse of the catalyst. This latter alternative gives rise to a broad group of process commonly known as “heterogeneous Fenton processes.” Finally, the combined use of Fenton’s reagent and electric current receives the generic denomination of “electro-Fenton techniques” [117].
The addition of iron salts as a catalyst in the presence of hydrogen peroxide is one of the classical methods of producing hydroxyl radicals, being one of the most powerful oxidizing agents at acidic pH (namely, pH = 3–5). The Fenton reagent has a great oxidizing capacity towards a wide range of organic substances, both aromatic (phenols, polyphenols, etc.) and aliphatic compounds (alcohols, aldehydes, etc.). The main oxidizing species is again the hydroxyl radical, which is generated in the initial reaction between hydrogen peroxide and Fe2+ salts [118]. While the exact mechanism of the oxidation of an organic compound by the reagent mentioned above is complex and not completely known, several authors agree on its main stages. Thus, it can be assumed that the overall process takes place through the following individual stages:
Fe2+ + H2O2 → Fe3+ + OH + OH
R + H2O2 → P1
R + ·OH → P2
where R represents the organic compound, and P1 and P2 are the formed intermediates and final products of the oxidation. The first reaction of the mechanism is responsible for the formation of hydroxyl radicals [118] that will later attack organic compound R in Reaction (41), the main degradation pathway in the Fenton reaction.
On the other hand, Reactions (34) and (42) represent the sequestering effect of such radicals exerted by Fe2+ itself or H2O2 [119]:
H2O2 + OH → HO2 + H2O
Fe2+ + OH → Fe3+ + OH
Finally, reactions (43), (44), and (45) indicate the possible reaction pathways of the Fe(III) generated in reaction (42) with H2O2 and with the hydroperoxide (HO2·) or superoxide (O2·) radicals.
Fe3+ + H2O2 → Fe2+ + H+ + HO2
Fe3+ + HO2· → Fe2+ + H+ + O2
Fe3+ + O2·→ Fe2+ + O2
It is worth noting that in Reactions (43)–(45), Fe2+ is regenerated, so that the Fenton process can be regarded as catalytic with respect to iron. Therefore, the reaction of formation of OH radicals can continue to take place as long as there is hydrogen peroxide in the medium.
For the procedure to be effective, the following requirements are necessary:
(a)
The pH of the water to be treated must be in the range 3–5 since at higher pH values, iron precipitates as Fe(OH)3, thus inactivating the system. Furthermore, if the pH is high, the decomposition of hydrogen peroxide into oxygen and water is favored.
(b)
The addition of the Fe2+ salt is necessary, generally as FeSO4, even though other sources of Fe2+ or Fe3+ can be added. In the case of Fe3+, which is also useful, a small initial delay of the reaction is observed.
(c)
The addition of H2O2 must be very slow to avoid decomposition phenomena.
The rate of ·OH radical generation, which in turn depends on the concentration of ferrous catalyst, generally limits the reaction rate of this system. The typical Fe2+: H2O2 molar ratio is 1: 5–10, although Fe2+ levels below 25–50 mg∙L−1 may require a considerable reaction time (10–48 h).
The main advantages of this oxidation process are:
(a)
Fe2+ is abundant and non-toxic.
(b)
Hydrogen peroxide is easy to handle and environmentally benign.
(c)
No chlorinated compounds are formed as in other techniques.
(d)
There are no limitations of matter transfer since the system is homogeneous. Hence, the design of reactors for this technology is quite simple.
(e)
An additional advantage of the Fenton process is the formation of complexes that promote the coagulation of suspended solids after oxidation reactions [120].
However, the Fenton process has some shortcomings, including:
(a)
The regeneration rate of Fe2+ from Fe3+ according to Reactions (43)–(45) is very low if compared with the depletion rate of Fe2+ (Reaction (42))
(b)
If pH increases above 3 or 3.5, large amounts of sludge are produced due to iron hydroxide precipitation, and additional treatment is necessary.
(c)
Fe2+ or Fe3+ ions may undergo complexation reactions with organic or inorganic ligands that may be present in solution.
(d)
Scavenging reactions may take place, for instance, Reaction (42).
In the absence of ferrous or ferric salt, there is no evidence of hydroxyl radical formation. As the iron concentration increases, the oxidation rate of organic compounds increases to a point at which an additional increase in iron concentration is ineffective. For most applications, it does not matter if Fe2+ or Fe3+ is used; the catalyst cycle starts quickly if hydrogen peroxide and organic material are in sufficient concentration.
When the H2O2 dose is increased, a noticeable reduction in organic matter is obtained, whereas a small or negligible change in toxicity may occur. Once a minimum threshold has been reached, small increases in the H2O2 dose result in evident decreases in the toxicity of the effluent. However, it must be kept in one’s mind that high concentrations of hydrogen peroxide lead to the scavenging of ·OH radicals (see Reactions (34)–(37)).
The reaction rate in the Fenton process increases with temperature, the effect being more pronounced at temperatures below 20 °C. However, when the temperature rises to 40–50 °C, the effectiveness of the reagent decreases. This is due to the accelerated decomposition of H2O2 into oxygen and water. From a practical standpoint, most of the commercial applications of this reagent occur at a temperature between 20–40 °C.
As indicated above, the optimum operational pH is between 3 and 3.5. The inefficiency of a basic pH is attributed to the transformation of the hydrated iron species to colloidal ferric species. In this last form, iron catalytically decomposes hydrogen peroxide into oxygen and water, without forming hydroxyl radicals.
This process can be applied to wastewater, sludge, or contaminated soils producing the oxidation of organic pollutants, reduction of toxicity, reduction of COD, reduction of BOD5, and elimination of odor and color. Some examples of the use of the Fenton process are summarized in Table 10.

4.3. The Fe3+/H2O2 System. Fenton-Like Reagent

The main drawback of using the Fenton system described above is the cost of the reagents, namely H2O2 and Fe2+. For this reason, several methods have been developed to substitute Fe2+ with Fe3+ salts, whose price is lower than that of the Fe2+ salts.
Originally, the “Fenton-like” term was used in reference to a similar process to that described in the previous section, with the only difference that the reagent used is a mixture of Fe3+ and H2O2 where the hydrogen peroxide decomposes into hydroxyl radicals, and the Fe(III) is reduced to Fe(II) following the reaction:
Fe3+ + H2O2 → Fe2+ + OH + OH
Several studies have shown that the decomposition rate of H2O2 and the oxidation rate of organic solutes are markedly slower using Fe3+/H2O2 than Fe2+/H2O2, with an optimal being achieved at pH = 3 [134,135].
Additionally, the Fenton-like process produces peroxyl radicals (HO2·):
Fe3+ + H2O2 → H+ + FeOOH2+
FeOOH2+→ HO2·+ Fe2+
Despite the fact that the homogeneous Fenton or Fenton-like processes have been largely used due to their effectiveness in terms of pollutant removal as well as to their ease of operation, both of them exhibit important disadvantages such as excessive sludge production and limited range of operational pH (usually below 3). Heterogeneous Fenton oxidation was developed to overcome these problems. In heterogeneous Fenton oxidation, a reaction takes place between hydrogen peroxide and Fe(III) in different forms, e.g., Fe2O3 or α-FeOOH, among others. If solid catalysts are used, in addition to the chemical reactions described above, physical adsorption occurs at the surface of the solid catalyst, which reduces sludge generation.
For all the exposure, the Fenton-like system is becoming progressively less used in recent years, and the number of manuscripts published is decreasing. On the contrary, heterogeneous Fenton-like processes, as well as those using different precursors to generate Fe(II) or Fe(III) ions in solution, are gaining importance. Hence, in this section, results corresponding not only to the Fenton-like process in its traditional sense, but also to some new alternatives will be presented.
Fe(II) used in the traditional Fenton process can be efficiently substituted by nanoscale zero-valent iron (nZVI) that is commonly synthesized by the reaction of Fe(II) with sodium borohydride:
Fe(H2O)62+ + 2 BH4 → Fe0↓ + 2 B(OH)3 + 7 H2
Once synthesized and/or isolated, Fe0 reacts with hydrogen peroxide or dissolved oxygen in the acidic medium required for the Fenton process (pH ~ 2.5–3.5) yielding Fe2+ as follows:
Fe0 + H2O2 + 2 H+ → Fe2+ + 2H2O
Fe0 + O2 + 2 H+ → Fe2+ + H2O2
Fe(II) undergoes the series of reactions described in the previous section. It is worth noting that Reaction (50) involves the degradation of hydrogen peroxide, whereas in Reaction (51), H2O2 is generated. Hence, the global reaction is:
2 Fe0 + O2 + 4 H+ → 2 Fe2+ + 2 H2O
However, the heterogeneous process appears to be less effective than a homogeneous Fenton process due to mass-transfer limitation. To solve this problem, different metal oxides, MOx (e.g., ceria [136], Fe3O4 [137], Mn3O4 [138], WMoO [139], FeCuO2, NiCuO2 [140], etc.) have been recently tested as catalysts or as a support of Fe0 in a series of alternative Fenton-like processes. The use of these oxides involves either a faster kinetic removal or the broadening of the operational pH range, that may reach up to 10 in some of these processes, which is not suitable for conventional Fenton or Fenton-like processes due to Fe(II) and/or Fe(III) precipitation in the form of hydroxides or oxyhydroxides.
The improvement in the performance of the MOx/ Fe0-catalyzed systems is attributable to different factors, mainly:
(a)
MOx usually exhibit larger specific surface areas than iron-based materials, thus favoring the adsorption of pollutants in the active sites of the solid’s surface.
(b)
MOx may act as catalysts for the homolytic break of H2O2 into two ·OH radicals.
(c)
MOx used to have a relatively large number of oxygen vacancies that are suitable for pollutants to react rapidly with the reactive oxygen species (ROS) generated on the material’s surface.
Biochar has also been used as catalyst support in Fenton-like processes [141]. It is well-known that the surface of biochars possesses a vast number and variety of redox-active sites (e.g., quinone, hydroquinone, conjugated π-electron systems, aromatic rings, etc.). These active sites are suitable to act as electron donors or acceptors in many redox processes such as Fenton-like, among others. Further details can be found in the excellent review recently published by Wang et al. (see reference [141] and citations therein).
Finally, the outstanding properties of graphene and graphene oxide have also been applied to the heterocatalytic Fenton-like process [142].
Table 11 summarizes some recent contributions regarding the removal of antibiotics through heterogeneous Fenton-like process

4.4. The Fe2+/H2O2/UV System (Photo- Fenton).

It is commonly accepted that UV radiation accelerates Fenton reactions, thus favoring the degree of degradation of organic pollutants, including aromatic and aliphatic compounds, and presenting greater effectiveness at acidic pH. The photo-Fenton system, therefore, includes ultraviolet radiation, hydrogen peroxide, and iron salts. This system has been considered one of the most promising ways of purifying highly contaminated wastewater [149,150].
The main advantages of the photo-Fenton process over the Fenton or Fenton-like reagents discussed in the previous section are the following:
(a)
The photolysis of hydrogen peroxide, produced according to Reaction (33), provides a supplementary source of ·OH radicals [101].
    Hν
H2O2 → 2 OH
(b)
The reduction of Fe3+ to Fe2+ by ultraviolet radiation, shown in Reaction (53), also contributes to the generation of hydroxyl radicals. Furthermore, this reaction facilitates the formation of Fe(II), which reacts rapidly with hydrogen peroxide to yield more ·OH radicals by the conventional Fenton reaction (39). Hence, it can be stated that UV radiation accelerates the Fe(III)–Fe(II) cycle, thus facilitating the production of hydroxyl radicals in both reactions (53) and (39)
Fe(OH) 2+ + hν → Fe2+ + OH
Fe2+ + H2O2 → Fe3+ +·OH + OH
In addition to these important advantages, Bossman et al. [151] proposed that Fe(III) in the presence of ultraviolet radiation is promoted into an excited state of Fe(III) that reacts faster with hydrogen peroxide to form Fe(II) and OH radicals, Reaction (46), or even with organic compounds.
Fe3+ + H2O2 → 2 Fe2+ + OH + OH
All these advantages make the photo-Fenton system a promising procedure in the treatment of water purification, since hydroxyl radicals are generated and secondary chlorinated oxidation products are not produced, as in the case of oxidation by chlorine or chlorine dioxide.
Table 12 summarizes some recent papers reporting the use of the photo-Fenton process for the removal of pharmaceuticals from water.
According to the literature, the photo-Fenton process is economical, technically simple, and highly efficient for the removal of pollutants in general and antibiotics in particular from wastewaters. Fe(II) salts, the H2SO4 required for acidic pH, and hydrogen peroxide are readily available chemicals. Furthermore, the use of UV radiation speeds up the generation of ·OH radicals, thus reducing the H2O2 consumption in comparison with the traditional Fenton process.

5. Heterogeneous Photocatalysis with TiO2

Photocatalysis is defined as the acceleration of a photochemical reaction by the presence of a semiconductor that is activated by the absorption of radiation with energy above its bandgap. The term heterogeneous refers to the fact that the contaminants are present in a fluid phase while the catalyst is in the solid phase. The most commonly used catalyst is titanium dioxide (TiO2) due to its high chemical stability, low cost, and excellent results it has proven to provide [158,159].
The first reaction of the photocatalysis process is the absorption of UV radiation by the catalyst, with the formation of hollow-electron (h+/e) pairs according to Reaction (54). In environmental applications, the photocatalytic processes are carried out under aerobic conditions, and oxygen can be adsorbed onto the catalyst’s surface. Hence, the aforementioned electrons, due to their high reducing power, reduce the oxygen adsorbed on the TiO2 surface, thus giving rise to the generation of superoxide radical ion (O2)·as indicated in Reaction (55); conversely, the holes are capable of causing the oxidation of water and/or HO adsorbed species into·OH radicals according to Reactions (56) and (57), which will subsequently oxidize the organic compounds. When organic matter is also adsorbed on the surface of the catalyst, it can be directly oxidized by the transfer of an electron from the catalyst [160]. Certainly, in the presence of redox species adsorbed on the semiconductor particle and under irradiation, oxidation and reduction reactions co-occur on the catalyst’s surface. The photogenerated holes give rise to photooxidation reactions, while the electrons in the conduction band give rise to photoreduction reactions:
TiO2 + hν → TiO2 (e) + TiO2(h+)
TiO2 (e) + O2 → TiO2 + O2·
TiO2(h+) + H2O → TiO2 + OH + H+
TiO2(h+) + HO → TiO2 + OH
The main advantages of this AOP are that it can be operated under pressure and at room temperature, the possibility of using sunlight for the irradiation of the catalyst, and the low cost and reusability of the catalyst. Also, this system is capable of achieving the complete mineralization of many compounds. However, it has significant disadvantages, such as the difficulties of attaining uniform radiation over the entire surface of the catalyst on a larger scale or the need for a subsequent separation treatment to recover the catalyst in suspension, which makes the process more expensive.

5.1. The TiO2/UV System

The process of photocatalytic oxidation, that is, the simultaneous application of air or oxygen, UV radiation, and a semiconductor (mainly TiO2), is a widely known process that is applied in the removal of numerous compounds but that is not fully developed on a large scale, mostly by the need to separate the photocatalyst, as indicated above. If used in powder (particle size in the range of tens of nm), TiO2 exhibits high effectiveness. It is also required that the incident radiation on the surface of the photocatalyst has a minimum of energy so that the electrons of the valence band of the semiconductor can be promoted to the conduction band and the generation of hole–electron pairs may take place. In the particular case of titanium dioxide, radiation in the near-ultraviolet is required. This is so because, unfortunately, TiO2 can absorb no more than 5% of the solar spectrum (i.e., the near UV light with λ < 380 nm) due to its relatively large bandgap (3.2 eV) [161]. As a consequence, the enhancement of the catalytic activity of TiO2 within the visible zone of the solar spectrum has received a great deal of attention by the scientific community in recent years. Different strategies have been followed to improve the photocatalytic properties of TiO2 under visible irradiation, such as surface modification with organic molecules [162] or nanoparticles [163,164] or doping with metal [163,165,166,167] and non-metal [165,168,169] ions, among others.
From the results summarized in Table 13, it may be concluded that the UV-TiO2 system is quite useful for the removal of antibiotics from water. However, authors agree that it is not the choice method to be applied for effluents showing high concentrations of pollutants. Furthermore, when large catalyst doses are used, the efficiency of the process decreases. Nevertheless, perhaps the main inconvenience that hinders the applicability of this method is the difficulty of separating and recycling an expensive photocatalyst as TiO2.

5.2. The TiO2/H2O2/UV System

It has already been stated that the simultaneous presence of H2O2 and UV radiation results in the homolytic photodissociation of the hydrogen peroxide molecule, thus giving rise to two hydroxyl radicals according to Reaction (33), see Section 5.1. Furthermore, the addition of hydrogen peroxide to the TiO2/UV system produces a considerable increase in the photodegradation rate. This effect may be due to the generation of more hydroxyl radicals by the reaction of H2O2 with the TiO2(e) generated when titanium dioxide is excited by radiation of the adequate wavelength (not necessarily UV light, as indicated under the previous section).
The reaction between TiO2(e) and H2O2 generates additional ·OH radicals easily available to contribute to oxidation processes:
TiO2(e) + H2O2 → TiO2 + OH + OH
As it is the case for the TiO2/UV system, the introduction of doping elements or surface modifications results in a better performance of the TiO2/H2O2/UV system both in terms of removal and mineralization efficiencies. For instance, Jiang et al. [175] have recently reported on the important role played by ferrihydrite (Fh) in the transference of the photo-generated electrons from TiO2 to H2O2. According to these authors, Fh deposited on the surface of the catalyst enables an improved separation of electron–hole pairs. These electrons are more available to be transferred to H2O2, thus enhancing its decomposition, Reaction (58), which results in more efficient degradation of the target antibiotic, cefotaxime. The Fh-TiO2 catalyst is highly active from the catalytic standpoint, is easy to prepare at relatively low cost, and exhibits good stability. Furthermore, according to the experimental data, catalytic activity continues even after the complete decomposition of H2O2 has taken place. Of course, the photo-generated electrons can also be directly transferred to dissolved O2, water, or H2O2 so that more hydroxyl and superoxide radicals are generated according to Reactions (55), (56), and (58), respectively.
Similarly, García-Muñoz et al. [176] have recently prepared a mesoporous Fe2O3-TiO2 catalyst that exhibited norfloxacin (NRF) degradation rates more than 60% greater than non-doped mesoporous titania. The maximum enhancement of the degradation rate occurs for 3 wt% Fe2O3-TiO2 catalyst, yielding 100% degradation and 90% mineralization within 120 min of reaction. According to the authors, in the hybrid photocatalyst iron oxidation-reduction reactions take place in the presence of H2O2, thus generating HOx· radical species that also contribute to the removal of NRF:
Fe(II)-TiO2 + H2O2→Fe(III)-TiO2 + HO·+ OH
Fe(II)-TiO2 + H2O2→Fe(III)-TiO2 + HOO·+ H+
Furthermore, oxidation of NRF in aqueous solutions occurs under mild reaction conditions, namely 25 °C and pH 7.

6. Sonochemical Advanced Oxidation Processes

Ultrasounds (US) are sound waves that have frequencies higher than those that can be perceived by the human ear (16 kHz) and lower than 1 GHz. US can be classified into different categories according to their frequency and intensity.
US of very high frequency and low intensity does not generate physicochemical modifications to the medium in which it is applied. US is used, for example, in medicine for diagnosis. High-intensity US, meanwhile, may interact with the medium. The interactions can be physical so that US is used to ease emulsification, cleaning up, and degassing. If the interactions are chemical, US can find applications in the synthesis of organic compounds and the degradation of pollutants in the environment, among others. This latter field of use of ultrasound is called sonochemistry.
In environmental applications, sonochemistry involves the application of US fields to an effluent, with a frequency between 20 kHz and 2 MHz. Among the various phenomena that appear in the water when an ultrasonic field propagates, ultrasonic cavitation stands out. Cavitation is defined as the phenomenon of formation, growth, and implosion of microbubbles or cavities within the liquid that takes place in a brief time interval (milliseconds) and releases a large amount of energy [158,159].
The generation of the phenomenon of cavitation depends mainly on the frequency and power of the US field. During this process, temperatures close to 5000 °C inside the bubbles and extremely high pressures (100 MPa) are generated locally and in a very short time, conditions that allow complicated chemical reactions to be carried out [177].
An aqueous solution in which cavitation takes place can be assimilated to an environment full of chemical microreactors (the cavitating bubbles) where at least the sonolysis of water takes place; that is, the homolytic breakdown of the molecule into highly reactive ·OH and H· radicals. The subsequent participation of these radicals, especially the OH radicals, in the oxidation of toxic and dangerous molecules that could be found in solution, makes it possible to suggest, at least theoretically, the feasibility of eliminating this type of pollutants without the need to use additional reagents—that can be dangerous—and under mild conditions of temperature or pressure [178]. Thus, the degradation of organic compounds can take place through the action of hydroxyl radicals (an oxidative mechanism) or due to high temperatures (a pyrolytic mechanism) [179].
When US is applied to an aqueous solution of a pollutant, the sonolysis of water may take place [180]:
2 H2O +))) ⟶ H2 + H2O2
and the generated H2O2 may also undergo sonolysis:
H2O2 +))) ⟶ 2 ·OH
Recently, Serna et al. [181] have reported the removal of up to 17 pharmaceuticals (nine of them antibiotics) by sonochemical oxidation. The authors propose a double mechanism for the degradation of the pollutants, namely pyrolysis, and interaction between pollutants and hydroxyl radicals. The former mechanism is responsible for the removal of hydrophobic and volatile species that undergo thermal degradation in the liquid–bubble interface. On the contrary, hydrophilic and nonvolatile compounds (including antibiotics) are oxidized by the ·OH radicals in the bulk solution.
However, the degradation efficiency and rate for most of the pollutants are far from being entirely satisfactory. The total mineralization of contaminants by the application of US alone is extremely difficult to achieve, particularly for refractory pollutants. Furthermore, the use of US in AOPs is inefficient from the energy consumption standpoint.
Nevertheless, sonication has successfully been applied as an auxiliary treatment in conjunction with other widely used AOPs and, particularly, with the Fenton reagent and some other derived from it.
For instance, in the so-called sono-Fenton process (Fe2+/H2O2/US), the following reactions are proposed [182]. The process initiates with two reactions that are coincident with the first stages of the Fenton process:
Fe2+ + H2O2 → Fe3+ + OH + OH
H2O2 + Fe3+ →Fe(OOH)2+ + H+
Next, the Fe(OOH)2+ decomposes sonochemically giving rise to hydroperoxyl radicals:
Fe(OOH)2+ +)))→ Fe2+ + HOO
Finally, additional sonochemically generated hydroxyl radicals become available for acting as oxidizing agents:
Fe2+ + HOO∙→ Fe2+ + H+ + O2
Fe2+ + H2O2→ Fe3+ + OH+ HO
According to Serna et al. [181] the removal of the pollutants in the effluent is more effective in the sono-Fenton process when compared with sonochemical oxidation alone, due to the generation of extra ·OH through reactions between Fe(II) and the sonogenerated hydrogen peroxide.
A similar situation has been described for the nZVI-based hetero-Fenton process, where nanoscaled Fe0 particles substitute Fe(II) in the initial stages of the process [182] as well as in the sono-Fenton-like process, where Fe(III) salts are used instead of Fe(II) [183]. This suggests that the use of a catalyst may improve energy consumption due to the occurrence of synergistic effects.
Zhou et al. [184] reported on the use of a goethite catalyst in the heterogeneous sonophotolytic Fenton-like (SP-FL) treatment of antibiotic sulfamethazine. The authors integrated the in situ H2O2 generation under UV illumination with a heterogeneous Fenton-like process and suggested that the synergistic role of US in the SP-FL system could be most ascribed to its promotional effect in Fenton-like reaction. Efficient Fe(II) species regeneration, improved mineralization degree, and successful wastewater detoxification were achieved.
Synergy appears to be more remarkable as the particle size of the catalyst decreases. Hence, the use of nanostructured catalysts is receiving a great deal of attention from the scientific community at present. Ghoreishian et al. [185] recently used flowerlike rGO/CdWO4 solar-light-responsive photocatalysts for the US-assisted heterogeneous degradation of tetracycline. Excellent photoelectrochemical behavior, superior sonophotocatalytic activity, and good mineralization efficiency were achieved under optimal conditions. Tetracycline was removed entirely at a pH of 5.7, an initial antibiotic concentration of 13.54 mg L−1, a treatment time of 60 min, and a catalyst dosage of 0.216 g L−1. Furthermore, rGO/CdWO4 exhibited a sonophotocatalytic efficiency that was 1.5 and 3 times higher than commercial nano–ZnO and nano–TiO2, respectively. Tetracycline was also chosen as the target pollutant by Vinesh et al. [186], which used a reduced graphene oxide (rGO)-supported electron-deficient B-doped TiO2 (Au/B-TiO2/rGO) nanocomposite. A considerable synergistic effect of ∼1.3 was observed when the reaction was performed in the presence of US and photocatalysis. The total degradation of the antibiotic was also confirmed by TOC analysis. The enhanced sonophotocatalytic activity was mainly attributed to the generation of more reactive species by the combination of US and photocatalysis. Also, Abazari et al. [187] applied Ni−Ti layered double hydroxide@graphitic carbon nitride nanosheet for photocatalytic and sonophotocatalytic removal of amoxicillin from aqueous solution. The authors related the enhancement in the sonophotocatalytic activity of the nanocomposites to their higher specific surface areas, the intimacy of the contact interfaces of their components, the synergistic effect between these components, and the restriction of electron−hole recombination. The optimum sonophotocatalysis conditions were 500 W light intensity, 9 s on/1 s off US pulse mode, and 1.25 g/L of g-C3N4@Ni−Ti LDH catalyst. Under these conditions, 99.5% removal within 75 min was attained.

7. Electro-Oxidative Advanced Oxidation Processes.

The application of electric current (from 2 to 20 A) between two electrodes in water produces the generation of hydroxyl ·OH radicals coupled with the production of hydrogen peroxide in the reaction medium.
H2O → OH + H+ + e
O2 + 2 H+ + 2 e → H2O2
The global reaction is:
2 H2O + O2 → H2O2 + 2 OH
Hence, the OH radicals can be regarded as the product of the anodic oxidation of water and are readily available to oxidize the organic matter in aqueous solution. At the same time, hydrogen peroxide is generated by cathodic reduction of oxygen [188].
Electro-oxidation, also called anodic oxidation or electrochemical incineration, is one of the most popular electrochemical advanced oxidation processes for the elimination of organic contaminants contained in wastewater [28,189].
This procedure involves the oxidation of the contaminants in an electrolytic cell through the following routes:
(a)
Direct electron transfer to the anode.
(b)
Indirect or mediated oxidation with oxidizing species formed from the electrolysis of water at the anode, by physisorbed OH radicals or by the chemisorbed “active oxygen.”
The existence of these species allows two different approaches to be proposed [190]:
(1)
Electrochemical conversion, where the refractory organic compounds are selectively transformed into biodegradable compounds, such as carboxylic acids, by the chemisorbed “active oxygen.”
(2)
Electrochemical combustion, where the physisorbed OH radicals mineralize the organic compounds.
Anodic oxidation can achieve the oxidation of water pollutants, either by direct contact or by oxidative processes that take place on the anodic surface of the electrochemical cell. Hence, the oxidation process does not necessarily have to occur in the anode, but it is initiated on its surface. As a consequence, this treatment combines two main types of processes [191]:
a.
Heterogeneous oxidation of contaminants on the surface of the anode. This is a complex process that consists of a series of simple steps: The transport of pollutants to the surface of the electrode, the adsorption of the contaminant on the electrode’s surface, the direct electrochemical reaction by electron transfer, the desorption of products, and the transport of such products to the dissolution.
b.
Homogeneous oxidation of contaminants by oxidants produced on the surface of the anode. These oxidizing species can be produced by the heterogeneous anodic oxidation of the water or from ions contained in the water acting in the dissolution of the electrolytic cell. The most important oxidant is the hydroxyl radical, which can be generated by the oxidation of water, Reaction (65), or by oxidation of the hydroxyl ion, Reaction (68):
H2O →·OHads + H+ + e
OH → OHads + e
The generation of this OH radical is the main argument for considering anodic oxidation as an AOP. Due to the high oxidation capacity of hydroxyl radicals, these promote the formation of many other oxidizing species (persulfates, peroxophosphates, ferrates, etc.) from different species contained in real water matrices [192]. It has been shown that the presence of these species has a significant effect on the increase in degradation efficiency [193]. The synergistic effects of all these mechanisms can explain the high efficiencies obtained in the elimination of pollutants and the high mineralization achieved with this technology in comparison with other AOPs [194].
Some materials lead to powerful oxidation of the pollutant, yielding CO2 and H2O as the major final products and a small number of intermediates, while other materials produce less oxidation and generate a large number of oxidation byproducts. Comninellis [195] proposed an integral model for the destruction of organic compounds in an acidic medium that assumes the existence of “non-active” and “active” anodes. According to this model, “active” anodes, which promote the electrochemical reaction of oxygen evolution, favor the electrochemical conversion of organic matter, while the “non-active”, which are less electrocatalytic for the evolution of oxygen, requiring higher anodic overpotentials, favor the electrochemical combustion of organic matter. In both types of anodes, denoted as M, the water oxidizes giving rise to the formation of physisorbed hydroxyl radicals (M (OH)):
M + H2O → M(·OH)physisorbed + H+ + e
In the case of “active” anodes, this radical interacts strongly with the surface, transforming into chemisorbed “active oxygen” or superoxide MO:
M(OH)physisorbed → MOchemisorbed + H+ + e
The MO/M pair is a mediator in the electrochemical conversion of organic compounds (R):
MO + R → M + RO
On the contrary, the surface of the “non-active” anodes interacts weakly with the OH species, so that these radicals react directly with the organic products until total mineralization is at least ideally achieved. These radicals are physisorbed on electroactive electrode sites and do not undergo modification during the electron transfer reaction.
Graphite electrodes, with sp2 carbon, metal (Pt, Ti/Pt), metal oxide (IrO2, RuO2), and mixed metal oxides electrodes, are considered as “active” anodes and behave as low-efficiency electrodes for the oxidation of organic compounds, generating a large number of intermediate byproducts. Most aromatic compounds treated with these anodes degrade slowly due to the generation of carboxylic acids that are difficult to oxidize [196]. Small mineralization efficiencies are obtained, and in some cases, polymeric species are generated, thus hindering the perspectives of application of these materials as anodes for electrooxidation processes.
Some metallic oxides and mixed metal oxides (those containing PbO2 and/or SnO2) and conductive diamond electrodes, in particular, the boron-doped diamond (BDD) electrodes are considered “non-active” anodes and behave as highly efficient electrodes for the oxidation of organic compounds. These anodes promote the mineralization of pollutants, whose extent is limited only by the mass transfer, and in general, virtually total mineralization of the contaminant is achieved. The surface material of BDD electrodes represents a promising technology for the electroanalysis of different biologically relevant active compounds [197,198,199,200,201].
In practice, all anodes exhibit a mixed behavior, since both mechanisms take place simultaneously. The “non-active” anodes may have defects in their surface or partially oxidized sites, while in the case of the “active” electrodes, the formation of physisorbed radicals at very positive potentials cannot be excluded, even if the surface is highly reactive. It should be mentioned that, as a general rule, the less positive the potential at which the evolution of oxygen occurs, the higher the participation of the anode surface in the reaction.
The generalized reaction pathway for the oxidation of an organic compound, R, and the simultaneous electrochemical formation of oxygen (over an anode, M), for the two types of anodes proposed, includes the following stages [202]:
(1)
Generation and adsorption of the·OH radical.
(2)
Oxygen production by electrochemical oxidation of adsorbed·OH radicals.
(3)
Formation of a site with a higher oxidation state by electrochemical oxidation of the radical OH.
(4)
Production of oxygen by chemical decomposition of the site with a higher oxidation state.
(5)
Combustion of the organic compound, R, by physisorbed·OH radicals.
(6)
Chemical oxidation of the organic compound at a site with a higher oxidation state.
The BDD anode is the most potent known “non-active” electrode [191]. It is considered as the most suitable anode for the treatment of organic compounds by anodic oxidation. Furthermore, the BDD electrodes have high anodic stability and a broad working potential range [203,204]. The use of BDD has considerably increased the interest in the application of this method in the treatment of waters since excellent mineralization efficiencies are obtained.
It should be noted that this anode exhibits excellent chemical and electrochemical stability, an inert surface with low adsorption properties, long life, and a wide range of potential for water discharge [205,206], and therefore, it turns out to be a promising electrode for the decontamination treatment.
The main limitation of technology based on BDD electrodes is its high price, which hinders its use at the industrial scale. It has been shown that many biorecalcitant compounds including phenols, chlorophenols, nitrophenols, pesticides, synthetic dyes, pharmaceuticals, and industrial leachates can be completely mineralized with high current efficiency, even close to 100%, using a BDD anode [207,208,209,210,211,212,213].
The composition of the supporting electrolyte or the different ions present in real industrial effluents can vary the effectiveness of the electrooxidation process. During the electrolysis with BDD anodes, simultaneously with the generation of active oxygen species that give rise to the generation of ·OH radicals, numerous reactions take place that can also lead to other oxidants depending on the ions present in the treated volume. In sulfate medium, oxidation of sulfate ions to peroxodisulfate can occur [209,214]:
2 SO42− ⟶ S2O82− + 2 e
A very particular behavior is found when the solution contains chloride ions since the electrogeneration of active chlorine in the form of chlorine gas, hypochlorous acid, or hypochlorite ion occurs through Reactions (73)–(75). Under these conditions, organic matter can be competitively attacked by the ·OH radicals produced on the surface of the anode and the active chlorine produced and diffused into the solution. As a counterpoint, the formation of organochlorine intermediates can occur, which can be even more stubborn and more toxic than the primary pollutants.
2 Cl → Cl2(aq) + 2 e
Cl2(aq) + H2O ↔ HClO + Cl + H+
HClO ↔ ClO + H+
When a “non-active” anode such as BDD is used, hypochlorite ions are also generated from the oxidation of chloride ions by the ·OH radicals adsorbed on the BDD anode according to Reaction (76). The resulting ion can be oxidized consecutively to chlorite, chlorate, and perchlorate according to Reactions (76)–(79) [215,216]:
Cl + OH → ClO + H+ + e
ClO +·OH → ClO2 + H+ + e
ClO2 + OH → ClO3 + H+ + e
ClO3 + OH → ClO4 + H++ e
It is worth mentioning that one of the most advanced large-scale applications in the field of electrochemical AOPs is the electrochemical disinfection of pool and spa water using automated equipment with BDD anodes. In this field, specialized products such as Oxineo™ and Sysneo™ have been developed for private and public facilities. Compared to other methods of disinfection, these systems have several advantages, since the chlorine smell typical of saline chlorination disappears, there is no accumulation of chemicals in the pool water—with the consequent reduction of allergic reactions—and there is no need to use anti-algae chemicals.

8. Prospects and Challenges of AOPs

From all the exposed in this review, AOPs arise as beneficial technologies for the removal of pollutants in general and antibiotics, in particular, that may be found in wastewaters. However, the applicability of these processes at the industrial scale is relatively limited at present.
Very recently, Rodríguez-Chueca et al. [217] have reported that AOPs, in general, improved the efficiency of UV-C on the removal of antibiotics. When applying the harshest operating conditions (0.5 mM dosage of oxidants and 7s of UV-C contact time), three antibiotics (ciprofloxacin, metronidazole, and sulfamethoxazole) were similarly removed using peroxymonosulfate and H2O2 as oxidants, four antibiotics (azithromycin, clindamycin, ofloxacin, and trimethoprim) were removed more efficiently using peroxymonosulfate, and three (clarithromycin, sulfadiazine, and sulfapyridine) using H2O2. The addition of Fe(II) only improved the degradation of four antibiotics (sulfamethoxazole, sulfadiazine, sulfapyridine, and metronidazole) compared to the photolytic process.
Chowdhury et al. [218] have studied the direct UV photolysis of different pharmaceutical compounds, including tetracycline antibiotics (chlortetracycline), sulfa drugs (sulfamethoxazole, sulfathiazole, and sulfisoxazole), and fluoroquinolones (ciprofloxacin) at full-scale. Except for ciprofloxacin, the remaining drugs showed considerable pH-dependent photolysis in the pH range under study (namely, 5–8). High removal by UV photolysis was attained, although a much higher UV fluence than that used for water disinfection was required. This latter finding suggests that additional treatments are necessary for water recycling.
Östman et al. [67] analyzed the effect of full-scale ozonation on the removal of up to eight antibiotics (namely, ciprofloxacin, norfloxacin, ofloxacin, pentamidine, clarithromycin, erythromycin, metronidazole, and trimethoprim) in Sweden’s first sewage treatment plant with full-scale ozonation. Ozonation proved to be effective in most cases. Total (100%) removal of ciprofloxacin and metronidazole was reported, whereas 94% was achieved for erythromycin (versus 79% in the conventional treatment). Trimethoprim was poorly removed (41%) in the traditional treatment process, but 94% removal efficiency was reached by ozonation.
Rame et al. [219] also indicate that FLASH technology that uses physical and biological pre-treatment, followed by an advanced oxidation process based on catalytic ozonation and followed by GAC and PAC filtration, has demonstrated good removal efficiency of macro-pollutants present in hospital wastewaters, including antibiotics.
Some years before, Sui et al. [220] reported that the sequential UV and ozonation process in a full-scale WWTP in Beijing was able to remove up to 13 pharmaceuticals and personal care products (PPCPs) including chloramphenicol. According to these authors, notwithstanding the fact that the UV exhibited a limited removal ability for most of the PPCPs under study, the sequential use of UV and ozone made it possible to minimize PPCPs in the final effluent of WWTPs.
To increase the feasibility of AOPs to be used at large scale, several aspects should be improved. With such an aim, further research work should be—and is currently being—performed on different topics such as, for instance, costs of the process, toxicity of effluents and byproducts, (photo)catalysts technology, and reactors design.
Many papers dealing with operational costs of AOPs at bench scale are available. However, articles focusing on operational expenses of full-scale advanced oxidation processes are scarce, and attention has been paid to this issue only in the last few years [46,221,222,223,224,225,226,227]. From the literature review, it may be concluded that treatment costs tend to decrease as the pollutant’s concentration in water increases. Moreover, the ozonation and Fenton processes appear to be more economically viable and, as a consequence, have been more frequently implemented at the industrial scale. However, authors do not agree on which of these treatments is the most cost-effective one. When integrating UV radiation to other AOPs, it can be stated that removal efficiencies increase, but operational costs are higher, too. Also, it is commonly accepted that photocatalysis (mainly using TiO2) is a relatively expensive AOP but also quite useful for the removal of pollutants.
In many cases, AOPs can be successfully applied for the removal of pollutants present in wastewaters and chemically degrade the parent compounds leading to their complete mineralization, thus generating CO2 and water as the leading products and without generation of any toxicity. However, it is not infrequent that the oxidation leads to different byproducts that may have similar—or even higher—toxicity than the original pollutants themselves. Changes in the molecular structure of the pollutant may give rise to an entirely new kind of chemical toxicity or even to mutagenic [228] or estrogenic activity [229]. For instance, during ozonation, the bromide naturally occurring in wastewater can be oxidized to bromate [230], with increasing yields as ozone dose rises [231]. Bromate is included in the EPA’s and EU’s lists of potential carcinogens. However, the addition of H2O2 largely mitigates the formation of bromate [232]. Similarly, if wastewaters contain large amounts of nitrate, the treatment by UV/H2O2 AOP may result in increased mutagenicity of the treated effluent [233]. According to the literature, the incorporation of the nitrate-nitrogen into the organic matrix and the subsequent formation on nitrated/nitrosated compounds could be the reason that mutagenicity levels increase in treated waters. Other authors have reported similar results in terms of increased toxicity after the treatment of wastewaters containing antibiotics [77,234,235,236,237,238].
Among the different alternatives to generate ·OH radicals in AOPs, heterogeneous photocatalysis appears as an up-and-coming solution in wastewater treatment. Photocatalysis is a nonselective process that can degrade a wide variety of pollutants. A photocatalyst (i.e., a semiconductor material) and light are the only requirements of this process. However, to the date, most of the results published in the literature focus on the use of UV irradiation, with wavelengths ranging from 320 to 400 nm, mainly because the bandgap of the semiconductor must be high enough to avoid fast recombination of the electron/hole pairs generated when the photoexcitation of the catalyst takes place. Different metal oxide semiconductors have been tested and used as potential photocatalysts for wastewater treatment. According to the literature [239], TiO2 and ZnO are the most widely used metal oxides in AOPs, even though other metal oxides (such as V2O5, WO3, MoO3, or some of their derivatives) or even sulfides (CdS, ZnS) could also be used. However, their performance is below that of TiO2. Furthermore, TiO2 exhibits essential advantages: It can be used under ambient conditions, is relatively inexpensive, commercially available, non-toxic, and photochemically stable.
An adequate modification of the chemical composition of the catalyst may result in enhanced efficiency and reusability. For instance, noble metals (Au, Pt, Ag, and Pd), transition metals (Cr, Mn, Fe, Co, Ni, Cu, and Zn) or lanthanides (La, Nd, Sm, Eu, Gd, Yb, or Pr) have been used as dopants in order to improve the photocatalytic activity of TiO2. The main goals of the chemical modification of TiO2 by using these dopants are: (i) To reduce the bandgap of the photocatalyst so that it is compatible with solar light (and not only with UV) to a solar light-compatible level; (ii) to maximize electron–hole generation; and (iii) to increase the adsorption ability of TiO2 towards organic pollutants by increasing its specific surface area [240,241,242].
Recently, a new group of materials, commonly known as two-dimensional (2D) nanomaterials, has shown promising properties to be used as novel photocatalysts and are receiving increasing attention from the scientific community [243]. These nanomaterials exhibit unique optical, electronic, and physicochemical properties, but their eventual applicability may be limited due to high production costs. 2D nanomaterials include graphene, graphitic carbon nitride (g-C3N4), 2D metal oxides and metallates, metal oxyhalides, and transition metal dichalcogenides. These materials can be applied alone as highly efficient photocatalysts. However, some of them exhibit better performance if they are combined with other “traditional” photocatalysts (e.g., TiO2), which, in turn, make them more affordable. For instance, it has been demonstrated that the use of graphene and TiO2 in the form of a heterojunction provides much higher photocatalytic efficiency than pure TiO2 [244].
Finally, another critical aspect to be taken into consideration is the proper design of the reactor. Fluidized bed reactor (FBR) has been successfully used in the full-scale application of AOPs in treatment plants [245] and is perhaps the most versatile option for this kind of processes. FBR has proven to be more effective in wastewater treatment compared to other conventional reactors such as, for instance, fixed-bed column and activated sludge. If FBR technology is combined with AOPs sludge production—one of the main disadvantages of the Fenton process—can be minimized [246], the reusability of the catalyst is increased [245], and the overall performance of the process is improved. FBRs exhibit remarkable advantages such as low operating cost, high resistance, uniformity of mixing, and high mass transfer rates. This latter is particularly important in the implementation of full-scale O3-based AOPS since one of the most significant drawbacks of ozone technologies is the difficulty of achieving an adequate mass transfer of gaseous ozone into the bulk solution. The most commonly investigated FBR-integrated AOPs are fluidized bed Fenton and fluidized bed photocatalysis. In the case of FBR heterogeneous Fenton process, high degradation efficiency has been achieved and the sludge generation has been reduced simultaneously [247]. On the other hand, in addition to its excellent mixing and mass transfer ability, in photocatalytic processes, the use of FBR can also enhance light penetration and exposure of the interior of the reaction matrix, thus improving the overall yield of the process in terms of pollutant(s) degradation.

9. Conclusions and Final Recommendations

Antibiotics are almost ubiquitous pollutants that have been found in different kinds of surface waters, wastewaters, and WWTP and hospital effluents. Furthermore, the presence of antibiotics in water may cause harmful effects to human beings as well as promote the spread of resistant bacterial strains. After several decades of research on AOPs, these technologies have proven their efficiency for the removal of a wide variety of pollutants in general and antibiotics in particular. However, most of the literature published to the date is devoted to bench- or pilot-scale studies. The implementation of AOPs at the full-scale is still quite limited. Probably, the main difficulty for the development of these processes at an industrially operative scale is the high operational cost of AOPs, especially if compared with the conventional methods that are commonly applied nowadays. Thus, if the overall cost per unit mass of pollutant that is removed from water or unit volume of water, wastewater, or effluent that is treated is lowered, the industrial implementation of these technologies will become much more attractive for companies and/or public administrations. Some suggestions on the way to achieve this goal are as follows:
(i)
To avoid unnecessary expenses in terms of time, facilities, and reagents, AOPs should be integrated with other treatments and only with specific and clearly defined goals (i.e., the removal of recalcitrant (micro)pollutants, the polishing of previously treated effluents, etc.). Furthermore, synergistic effects between processes should be studied at least at the pilot-scale.
(ii)
Energy costs must also be reduced. In this connection, the search for novel, affordable photocatalysts that may use a broader part of the light spectrum instead of only UV is a priority. Furthermore, the application of renewable energy sources in the treatment plants should also be investigated.
(iii)
The generation of wastes (e.g., sludge in the Fenton process and/or exhausted or poisoned catalysts in photocatalyzed AOPs), should be minimized and possible alternatives for the valorization of such wastes should be explored.

Author Contributions

Conceptualization, E.M.C.-C.; bibliographical search, E.M.C.-C., M.F.A.-F. and C.F.-G.; formal analysis of Photolysis and Ozone-based AOPs, E.M.C.-C. and M.F.A.-F.; formal analysis of Hydrogen peroxide-based AOPs, M.F.A.-F. and C.F.-G.; formal analysis of Heterogeneous photocatalysis, E.M.C.-C. and C.F.-G.; formal analysis of Sonochemical and Electro-oxidative AOPs, E.M.C.-C. and M.F.A.-F.; formal analysis of Prospects and challenges of AOPs, E.M.C.-C., M.F.A.-F. and C.F.-G.; writing—original draft preparation, E.M.C.-C., M.F.A.-F. and C.F.-G.; writing—review and editing, E.M.C.-C; supervision, E.M.C.-C. All authors have read and agreed to the published version of the manuscript.

Funding

This research received no external funding.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. NESCO and World Health Organization. Progress on Drinking Water and Sanitation: 2012 Update; UNICEF, Division of Communication: New York, NY, USA, 2012; ISBN 9789280646320. [Google Scholar]
  2. UNESCO. The 1st UN World Water Development Summary Report; UNESCO: London, UK, 2003; Volume 36. [Google Scholar]
  3. United Nations. Water A Shared Responsibility The United Nations World Water Development Report 2 Berghahn Books; UNICEF, Division of Communication: San Francisco, CA, USA, 2006; ISBN 9231040065. [Google Scholar]
  4. Brillas, E.; Sirés, I.; Oturan, M.A. Electro-fenton process and related electrochemical technologies based on fenton’s reaction chemistry. Chem. Rev. 2009, 109, 6570–6631. [Google Scholar] [CrossRef] [PubMed]
  5. Relyea, R.A. New effects of Roundup on amphibians: Predators reduce herbicide mortality; Herbicides induce antipredator morphology. Ecol. Appl. 2012, 22, 634–647. [Google Scholar] [CrossRef] [PubMed]
  6. Petrović, M.; Gonzalez, S.; Barceló, D. Analysis and removal of emerging contaminants in wastewater and drinking water. TrAC Trends Anal. Chem. 2003, 22, 685–696. [Google Scholar] [CrossRef] [Green Version]
  7. Farré, M.L.; Pérez, S.; Kantiani, L.; Barceló, D. Fate and toxicity of emerging pollutants, their metabolites and transformation products in the aquatic environment. TrAC Trends Anal. Chem. 2008, 27, 991–1007. [Google Scholar] [CrossRef]
  8. Gagné, F.; Blaise, C.; André, C. Occurrence of pharmaceutical products in a municipal effluent and toxicity to rainbow trout (Oncorhynchus mykiss) hepatocytes. Ecotoxicol. Environ. Saf. 2006, 64, 329–336. [Google Scholar] [CrossRef]
  9. Halling-Sørensen, B.; Nors Nielsen, S.; Lanzky, P.F.; Ingerslev, F.; Holten Lützhøft, H.C.; Jørgensen, S.E. Occurrence, fate and effects of pharmaceutical substances in the environment—A review. Chemosphere 1998, 36, 357–393. [Google Scholar] [CrossRef]
  10. Huber, M.M.; Göbel, A.; Joss, A.; Hermann, N.; Löffler, D.; McArdell, C.S.; Ried, A.; Siegrist, H.; Ternes, T.A.; Von Gunten, U. Oxidation of pharmaceuticals during ozonation of municipal wastewater effluents: A pilot study. Environ. Sci. Technol. 2005, 39, 4290–4299. [Google Scholar] [CrossRef]
  11. Santos, L.H.M.L.M.; Araújo, A.N.; Fachini, A.; Pena, A.; Delerue-Matos, C.; Montenegro, M.C.B.S.M. Ecotoxicological aspects related to the presence of pharmaceuticals in the aquatic environment. J. Hazard. Mater. 2010, 175, 45–95. [Google Scholar] [CrossRef] [Green Version]
  12. Joss, A.; Keller, E.; Alder, A.C.; Göbel, A.; McArdell, C.S.; Ternes, T.; Siegrist, H. Removal of pharmaceuticals and fragrances in biological wastewater treatment. Water Res. 2005, 39, 3139–3152. [Google Scholar] [CrossRef]
  13. Joss, A.; Zabczynski, S.; Göbel, A.; Hoffmann, B.; Löffler, D.; McArdell, C.S.; Ternes, T.A.; Thomsen, A.; Siegrist, H. Biological degradation of pharmaceuticals in municipal wastewater treatment: Proposing a classification scheme. Water Res. 2006, 40, 1686–1696. [Google Scholar] [CrossRef]
  14. Lee, Y.; Von Gunten, U. Oxidative transformation of micropollutants during municipal wastewater treatment: Comparison of kinetic aspects of selective (chlorine, chlorine dioxide, ferrateVI, and ozone) and non-selective oxidants (hydroxyl radical). Water Res. 2010, 44, 555–566. [Google Scholar] [CrossRef] [PubMed]
  15. Fewson, C.A. Biodegradation of xenobiotic and other persistent compounds: The causes of recalcitrance. Trends Biotechnol. 1988, 6, 148–153. [Google Scholar] [CrossRef]
  16. López, R.; Menéndez, M.I.; Díaz, N.; Suárez, D.; Campomanes, P.; Ardura, D.; Sordo, T.L. Theoretical studies on the ring opening of β-lactams: Processes in solution and in enzymatic media. Curr. Org. Chem. 2006, 10, 805–821. [Google Scholar] [CrossRef]
  17. Robinson, T.; McMullan, G.; Marchant, R.; Nigam, P. Remediation of dyes in textile effluent: A critical review on current treatment technologies with a proposed alternative. Bioresour. Technol. 2001, 77, 247–255. [Google Scholar] [CrossRef]
  18. Forgacs, E.; Cserháti, T.; Oros, G. Removal of synthetic dyes from wastewaters: A review. Environ. Int. 2004, 30, 953–971. [Google Scholar] [CrossRef]
  19. Glaze, W.H.; Kang, J.W.; Chapin, D.H. The chemistry of water treatment processes involving ozone, hydrogen peroxide and ultraviolet radiation. Ozone Sci. Eng. 1987, 9, 335–352. [Google Scholar] [CrossRef]
  20. Ayoub, K.; van Hullebusch, E.D.; Cassir, M.; Bermond, A. Application of advanced oxidation processes for TNT removal: A review. J. Hazard. Mater. 2010, 178, 10–28. [Google Scholar] [CrossRef]
  21. Legrini, O.; Oliveros, E.; Braun, A.M. Photochemical Processes for Water Treatment. Chem. Rev. 1993, 93, 671–698. [Google Scholar] [CrossRef]
  22. Klavarioti, M.; Mantzavinos, D.; Kassinos, D. Removal of residual pharmaceuticals from aqueous systems by advanced oxidation processes. Environ. Int. 2009, 35, 402–417. [Google Scholar] [CrossRef]
  23. Malato, S.; Fernández-Ibáñez, P.; Maldonado, M.I.; Blanco, J.; Gernjak, W. Decontamination and disinfection of water by solar photocatalysis: Recent overview and trends. Catal. Today 2009, 147, 1–59. [Google Scholar] [CrossRef]
  24. Haag, W.R.; David Yao, C.C. Rate Constants for Reaction of Hydroxyl Radicals with Several Drinking Water Contaminants. Environ. Sci. Technol. 1992, 26, 1005–1013. [Google Scholar] [CrossRef]
  25. Garcia-Segura, S.; El-Ghenymy, A.; Centellas, F.; Rodríguez, R.M.; Arias, C.; Garrido, J.A.; Cabot, P.L.; Brillas, E. Comparative degradation of the diazo dye Direct Yellow 4 by electro-Fenton, photoelectro-Fenton and photo-assisted electro-Fenton. J. Electroanal. Chem. 2012, 681, 36–43. [Google Scholar] [CrossRef]
  26. Guinea, E.; Arias, C.; Cabot, P.L.; Garrido, J.A.; Rodríguez, R.M.; Centellas, F.; Brillas, E. Mineralization of salicylic acid in acidic aqueous medium by electrochemical advanced oxidation processes using platinum and boron-doped diamond as anode and cathodically generated hydrogen peroxide. Water Res. 2008, 42, 499–511. [Google Scholar] [CrossRef] [PubMed]
  27. Pera-Titus, M.; García-Molina, V.; Baños, M.A.; Giménez, J.; Esplugas, S. Degradation of chlorophenols by means of advanced oxidation processes: A general review. Appl. Catal. B Environ. 2004, 47, 219–256. [Google Scholar] [CrossRef]
  28. Martínez-Huitle, C.A.; Ferro, S. Electrochemical oxidation of organic pollutants for the wastewater treatment: Direct and indirect processes. Chem. Soc. Rev. 2006, 35, 1324–1340. [Google Scholar] [CrossRef]
  29. Serra, A.; Domènech, X.; Arias, C.; Brillas, E.; Peral, J. Oxidation of α-methylphenylglycine under Fenton and electro-Fenton conditions in the dark and in the presence of solar light. Appl. Catal. B Environ. 2009, 89, 12–21. [Google Scholar] [CrossRef]
  30. Feng, L.; Van Hullebusch, E.D.; Rodrigo, M.A.; Esposito, G.; Oturan, M.A. Removal of residual anti-inflammatory and analgesic pharmaceuticals from aqueous systems by electrochemical advanced oxidation processes. A review. Chem. Eng. J. 2013, 228, 944–964. [Google Scholar] [CrossRef]
  31. Sirés, I.; Brillas, E.; Oturan, M.A.; Rodrigo, M.A.; Panizza, M. Electrochemical advanced oxidation processes: Today and tomorrow. A review. Environ. Sci. Pollut. Res. 2014, 21, 8336–8367. [Google Scholar] [CrossRef]
  32. Andreozzi, R.; Caprio, V.; Insola, A.; Marotta, R. Advanced oxidation processes (AOP) for water purification and recovery. Catal. Today 1999, 53, 51–59. [Google Scholar] [CrossRef]
  33. Bokare, A.D.; Choi, W. Review of iron-free Fenton-like systems for activating H2O2 in advanced oxidation processes. J. Hazard. Mater. 2014, 275, 121–135. [Google Scholar] [CrossRef]
  34. Ince, N.H.; Apikyan, I.G. Combination of activated carbon adsorption with light-enhanced chemical oxidation via hydrogen peroxide. Water Res. 2000, 34, 4169–4176. [Google Scholar] [CrossRef]
  35. Anjali, R.; Shanthakumar, S. Insights on the current status of occurrence and removal of antibiotics in wastewater by advanced oxidation processes. J. Environ. Manag. 2019, 246, 51–62. [Google Scholar] [CrossRef] [PubMed]
  36. Bartolomeu, M.; Neves, M.G.P.M.S.; Faustino, M.A.F.; Almeida, A. Wastewater chemical contaminants: Remediation by advanced oxidation processes. Photochem. Photobiol. Sci. 2018, 17, 1573–1598. [Google Scholar] [CrossRef] [PubMed]
  37. Bousiakou, L.; Kazi, M.; Lianos, P. Wastewater treatment technologies in the degradation of hormones and pharmaceuticals with focus on TiO2 technologies. Pharmakeftiki 2013, 25, 37–48. [Google Scholar]
  38. Daghrir, P.; Drogui, R. Tetracycline antibiotics in the environment: A review. Environ. Chem. Lett. 2013, 11, 209–227. [Google Scholar] [CrossRef]
  39. Rivera-Utrilla, J.; Sánchez-Polo, M.; Ferro-García, M.Á.; Prados-Joya, G. Pharmaceuticals as emerging contaminants and their removal from water: A review. Chemosphere 2013, 93, 1268–1287. [Google Scholar] [CrossRef]
  40. Oller, I.; Malato, S.; Sánchez-pérez, J.A. Combination of Advanced Oxidation Processes and biological treatments for wastewater decontamination—A review. Sci. Total Environ. 2011, 409, 4141–4166. [Google Scholar] [CrossRef]
  41. Homem, V.; Santos, L. Degradation and removal methods of antibiotics from aqueous matrices—A review. J. Environ. Manag. 2011, 92, 2304–2347. [Google Scholar] [CrossRef]
  42. Yargeau, V.; Leclair, C.; Yargeau, V.; Leclair, C. Impact of Operating Conditions on Decomposition of Antibiotics During Ozonation: A Review Impact of Operating Conditions on Decomposition of Antibiotics During Ozonation: A Review. Ozone Sci. Eng. 2008, 30, 175–188. [Google Scholar] [CrossRef]
  43. Esplugas, S.; Bila, D.M.; Gustavo, L.; Krause, T. Ozonation and advanced oxidation technologies to remove endocrine disrupting chemicals (EDCs) and pharmaceuticals and personal care products ( PPCPs ) in water effluents. J. Hazard. Mater. 2007, 149, 631–642. [Google Scholar] [CrossRef]
  44. Ikehata, K.; Naghashkar, N.J.; El-din, M.G.; Ikehata, K.; Naghashkar, N.J.; El-din, M.G. Degradation of Aqueous Pharmaceuticals by Ozonation and Advanced Oxidation Processes: A Review. Ozone Sci. Eng. 2007, 28, 353–414. [Google Scholar] [CrossRef]
  45. Jain, B.; Kumar, A.; Hyunook, S.; Eric, K.; Virender, L. Treatment of organic pollutants by homogeneous and heterogeneous Fenton reaction processes. Environ. Chem. Lett. 2018, 16, 947–967. [Google Scholar] [CrossRef] [Green Version]
  46. Lofrano, G.; Pedrazzani, R.; Libralato, G.; Carotenuto, M. Advanced Oxidation Processes for Antibiotics Removal: A Review. Curr. Org. Chem. 2017, 21, 1–14. [Google Scholar] [CrossRef]
  47. Yan, S.; Song, W. Photo-transformation of pharmaceutically active compounds in the aqueous environment: A review. Environ. Sci. Process. Impacts 2014, 16, 697–720. [Google Scholar] [CrossRef]
  48. Oppenländer, T. Photochemical Purification of Water and Air: Advanced Oxidation Processes (AOPs): Principles, Reaction Mechanisms, Reactor Concepts; Wiley-VCH Verlag GmbH & Co.: Weinheim, Germany, 2002. [Google Scholar]
  49. Timm, A.; Borowska, E.; Majewsky, M.; Merel, S.; Zwiener, C.; Bräse, S.; Horn, H. Photolysis of four β-lactam antibiotics under simulated environmental conditions: Degradation, transformation products and antibacterial activity. Sci. Total Environ. 2019, 651, 1605–1612. [Google Scholar] [CrossRef]
  50. Wang, X.H.; Lin, A.Y.C. Phototransformation of Cephalosporin Antibiotics in an Aqueous Environment Results in Higher Toxicity. Environ. Sci. Technol. 2012, 46, 12417–12426. [Google Scholar] [CrossRef]
  51. Jiang, M.; Wang, L.; Ji, R. Biotic and abiotic degradation of four cephalosporin antibiotics in a lake surface water and sediment. Chemosphere 2010, 80, 1399–1405. [Google Scholar] [CrossRef]
  52. Ribeiro, A.R.; Lutze, H.V.; Schmidt, T.C. Base-catalyzed hydrolysis and speciation-dependent photolysis of two cephalosporin antibiotics, ceftiofur and cefapirin. Water Res. 2018, 134, 253–260. [Google Scholar] [CrossRef]
  53. Wei, X.; Chen, J.; Xie, Q.; Zhang, S.; Ge, L.; Qiao, X. Distinct photolytic mechanisms and products for different dissociation species of ciprofloxacin. Environ. Sci. Technol. 2013, 47, 4284–4290. [Google Scholar] [CrossRef]
  54. Prabhakaran, D.; Sukul, P.; Lamshöft, M.; Maheswari, M.A.; Zühlke, S.; Spiteller, M. Photolysis of difloxacin and sarafloxacin in aqueous systems. Chemosphere 2009, 77, 739–746. [Google Scholar] [CrossRef]
  55. Lastre-Acosta, A.M.; Barberato, B.; Parizi, M.P.S.; Teixeira, A.C.S.C. Direct and indirect photolysis of the antibiotic enoxacin: Kinetics of oxidation by reactive photo-induced species and simulations. Environ. Sci. Pollut. Res. 2019, 26, 4337–4347. [Google Scholar] [CrossRef] [PubMed] [Green Version]
  56. Baena-Nogueras, R.M.; González-Mazo, E.; Lara-Martín, P.A. Photolysis of Antibiotics under Simulated Sunlight Irradiation: Identification of Photoproducts by High-Resolution Mass Spectrometry. Environ. Sci. Technol. 2017, 51, 3148–3156. [Google Scholar] [CrossRef] [PubMed]
  57. Niu, J.; Zhang, L.; Li, Y.; Zhao, J.; Lv, S.; Xiao, K. Effects of environmental factors on sulfamethoxazole photodegradation under simulated sunlight irradiation: Kinetics and mechanism. J. Environ. Sci. 2013, 25, 1098–1106. [Google Scholar] [CrossRef]
  58. López-Peñalver, J.J.; Sánchez-Polo, M.; Gómez-Pacheco, C.V.; Rivera-Utrilla, J. Photodegradation of tetracyclines in aqueous solution by using UV and UV/H2O2 oxidation processes. J. Chem. Technol. Biotechnol. 2010, 85, 1325–1333. [Google Scholar] [CrossRef]
  59. Ryan, C.C.; Tan, D.T.; Arnold, W.A. Direct and indirect photolysis of sulfamethoxazole and trimethoprim in wastewater treatment plant effluent. Water Res. 2011, 45, 1280–1286. [Google Scholar] [CrossRef]
  60. Shu, H.Y.; Chang, M.C. Decolorization and mineralization of a phthalocyanine dye C.I. Direct Blue 199 using UV/H2O2 process. J. Hazard. Mater. 2005, 125, 96–101. [Google Scholar] [CrossRef]
  61. Wols, B.A.; Hofman-Caris, C.H.M. Review of photochemical reaction constants of organic micropollutants required for UV advanced oxidation processes in water. Water Res. 2012, 46, 2815–2827. [Google Scholar] [CrossRef]
  62. Katsoyiannis, I.A.; Canonica, S.; Von Gunten, U. Efficiency and energy requirements for the transformation of organic micropollutants by ozone, O3/H2O2 and UV/H2O2. Water Res. 2011, 45, 3811–3822. [Google Scholar] [CrossRef]
  63. Andreozzi, R.; Canterino, M.; Marotta, R.; Paxeus, N. Antibiotic removal from wastewaters: The ozonation of amoxicillin. J. Hazard. Mater. 2005, 122, 243–250. [Google Scholar] [CrossRef]
  64. Arslan-Alaton, I.; Dogruel, S. Pre-treatment of penicillin formulation effluent by advanced oxidation processes. J. Hazard. Mater. 2004, 112, 105–113. [Google Scholar] [CrossRef]
  65. Alsager, O.A.; Alnajrani, M.N.; Abuelizz, H.A.; Aldaghmani, I.A. Removal of antibiotics from water and waste milk by ozonation: Kinetics, byproducts, and antimicrobial activity. Ecotoxicol. Environ. Saf. 2018, 158, 114–122. [Google Scholar] [CrossRef] [PubMed]
  66. Witte, B.D.; Langenhove, H.V.; Hemelsoet, K.; Demeestere, K.; Wispelaere, P.D.; Van Speybroeck, V.; Dewulf, J. Levofloxacin ozonation in water: Rate determining process parameters and reaction pathway elucidation. Chemosphere 2009, 76, 683–689. [Google Scholar] [CrossRef] [PubMed]
  67. Östman, M.; Björlenius, B.; Fick, J.; Tysklind, M. Effect of full-scale ozonation and pilot-scale granular activated carbon on the removal of biocides, antimycotics and antibiotics in a sewage treatment plant. Sci. Total Environ. 2019, 649, 1117–1123. [Google Scholar] [CrossRef] [PubMed]
  68. Ternes, T.A.; Stüber, J.; Herrmann, N.; McDowell, D.; Ried, A.; Kampmann, M.; Teiser, B. Ozonation: A tool for removal of pharmaceuticals, contrast media and musk fragrances from wastewater? Water Res. 2003, 37, 1976–1982. [Google Scholar] [CrossRef]
  69. Lange, F.; Cornelissen, S.; Kubac, D.; Sein, M.M.; Von Sonntag, J.; Hannich, C.B.; Golloch, A.; Heipieper, H.J.; Möder, M.; Von Sonntag, C. Degradation of macrolide antibiotics by ozone: A mechanistic case study with clarithromycin. Chemosphere 2006, 65, 17–23. [Google Scholar] [CrossRef]
  70. Feng, M.; Yan, L.; Zhang, X.; Sun, P.; Yang, S.; Wang, L.; Wang, Z. Fast removal of the antibiotic flumequine from aqueous solution by ozonation: Influencing factors, reaction pathways, and toxicity evaluation. Sci. Total Environ. 2016, 541, 167–175. [Google Scholar] [CrossRef]
  71. Qiang, Z.; Adams, C.; Surampalli, R. Determination of ozonation rate constants for lincomycin and spectinomycin. Ozone Sci. Eng. 2004, 26, 525–537. [Google Scholar] [CrossRef]
  72. Andreozzi, R.; Canterino, M.; Giudice, R.L.; Marotta, R.; Pinto, G.; Pollio, A. Lincomycin solar photodegradation, algal toxicity and removal from wastewaters by means of ozonation. Water Res. 2006, 40, 630–638. [Google Scholar] [CrossRef]
  73. Wang, H.; Mustafa, M.; Yu, G.; Östman, M.; Cheng, Y.; Wang, Y.; Tysklind, M. Oxidation of emerging biocides and antibiotics in wastewater by ozonation and the electro-peroxone process. Chemosphere 2019, 235, 575–585. [Google Scholar] [CrossRef]
  74. Hirasawa, I.; Kaneko, S.; Kanai, Y.; Hosoya, S.; Okuyama, K.; Kamahara, T.; Adnan, A.; Mavinic, D.S.; Koch, F.A.; Villarroel Walker, R.; et al. Pilot-scale study of phosphorus recovery through struvite crystallization – examining the process feasibility. J. Environ. Manag. 2003, 37, 315–324. [Google Scholar]
  75. Huber, M.M.; Canonica, S.; Park, G.Y.; Von Gunten, U. Oxidation of pharmaceuticals during ozonation and advanced oxidation processes. Environ. Sci. Technol. 2003, 37, 1016–1024. [Google Scholar] [CrossRef] [PubMed]
  76. Garoma, T.; Umamaheshwar, S.K.; Mumper, A. Removal of sulfadiazine, sulfamethizole, sulfamethoxazole, and sulfathiazole from aqueous solution by ozonation. Chemosphere 2010, 79, 814–820. [Google Scholar] [CrossRef] [PubMed]
  77. Dantas, R.F.; Contreras, S.; Sans, C.; Esplugas, S. Sulfamethoxazole abatement by means of ozonation. J. Hazard. Mater. 2008, 150, 790–794. [Google Scholar] [CrossRef] [PubMed]
  78. Kim, T.-H.; Kim, S.D.; Kim, H.Y.; Lim, S.J.; Lee, M.; Yu, S. Degradation and toxicity assessment of sulfamethoxazole and chlortetracycline using electron beam, ozone and UV. J. Hazard. Mater. 2012, 227, 237–242. [Google Scholar] [CrossRef] [PubMed]
  79. Chen, X.; Richard, J.; Liu, Y.; Dopp, E.; Tuerk, J.; Bester, K. Ozonation products of triclosan in advanced wastewater treatment. Water Res. 2012, 46, 2247–2256. [Google Scholar] [CrossRef]
  80. Stylianou, S.K.; Katsoyiannis, I.A.; Mitrakas, M.; Zouboulis, A.I. Application of a ceramic membrane contacting process for ozone and peroxone treatment of micropollutant contaminated surface water. J. Hazard. Mater. 2018, 358, 129–135. [Google Scholar] [CrossRef]
  81. Peyton, G.R.; Glaze, W.H. Destruction of pollutants in water with ozone in combination with ultraviolet radiation. 3. Photolysis of aqueous ozone. Environ. Sci. Technol. 1988, 22, 761–767. [Google Scholar] [CrossRef]
  82. Litter, M.I.; Quici, N. Photochemical Advanced Oxidation Processes for Water and Wastewater Treatment. Recent Patents Eng. 2010, 4, 217–241. [Google Scholar] [CrossRef]
  83. Morkovnik, A.F.; Okhlobystin, O.Y. Inorganic radical-ions and their organic reactions. Russ. Chem. Rev. 1979, 48, 1055–1075. [Google Scholar] [CrossRef]
  84. Benitez, F.J.; Acero, J.L.; Real, F.J.; Roldan, G.; Casas, F. Comparison of different chemical oxidation treatments for the removal of selected pharmaceuticals in water matrices. Chem. Eng. J. 2011, 168, 1149–1156. [Google Scholar] [CrossRef]
  85. Liu, P.; Zhang, H.; Feng, Y.; Yang, F.; Zhang, J. Removal of trace antibiotics from wastewater: A systematic study of nanofiltration combined with ozone-based advanced oxidation processes. Chem. Eng. J. 2014, 240, 211–220. [Google Scholar] [CrossRef]
  86. Paucar, N.E.; Kim, I.; Tanaka, H.; Sato, C.; Paucar, N.E.; Kim, I.; Tanaka, H.; Sato, C. Effect of O3 Dose on the O3/UV Treatment Process for the Removal of Pharmaceuticals and Personal Care Products in Secondary Effluent. ChemEngineering 2019, 3, 53. [Google Scholar] [CrossRef] [Green Version]
  87. Lester, Y.; Avisar, D.; Gozlan, I.; Mamane, H. Removal of pharmaceuticals using combination of UV/H2O2/O3 advanced oxidation process. Water Sci. Technol. 2011, 64, 2230–2238. [Google Scholar] [CrossRef] [PubMed]
  88. Yao, W.; Ur Rehman, S.W.; Wang, H.; Yang, H.; Yu, G.; Wang, Y. Pilot-scale evaluation of micropollutant abatements by conventional ozonation, UV/O3, and an electro-peroxone process. Water Res. 2018, 138, 106–117. [Google Scholar] [CrossRef] [PubMed]
  89. Beltrán, F.J.; Aguinaco, A.; García-Araya, J.F.; Oropesa, A. Ozone and photocatalytic processes to remove the antibiotic sulfamethoxazole from water. Water Res. 2008, 42, 3799–3808. [Google Scholar] [CrossRef]
  90. Glaze, W.H.; Beltran, F.; Tuhkanen, T.; Kang, J.W. Chemical models of advanced oxidation processes. Water Pollut. Res. J. Can. 1992, 27, 23–42. [Google Scholar] [CrossRef]
  91. De Witte, B.; Dewulf, J.; Demeestere, K.; Van Langenhove, H. Ozonation and advanced oxidation by the peroxone process of ciprofloxacin in water. J. Hazard. Mater. 2009, 161, 701–708. [Google Scholar] [CrossRef]
  92. Rosal, R.; Rodríguez, A.; Perdigón-Melón, J.A.; Mezcua, M.; Hernando, M.D.; Letón, P.; García-Calvo, E.; Agüera, A.; Fernández-Alba, A.R. Removal of pharmaceuticals and kinetics of mineralization by O3/H2O2 in a biotreated municipal wastewater. Water Res. 2008, 42, 3719–3728. [Google Scholar] [CrossRef]
  93. Gomes, D.S.; Gando-Ferreira, L.M.; Quinta-Ferreira, R.M.; Martins, R.C. Removal of sulfamethoxazole and diclofenac from water: Strategies involving O3 and H2O2. Environ. Technol. 2018, 39, 1658–1669. [Google Scholar] [CrossRef]
  94. Qin, W.; Song, Y.; Dai, Y.; Qiu, G.; Ren, M.; Zeng, P. Treatment of berberine hydrochloride pharmaceutical wastewater by O3/UV/H2O2 advanced oxidation process. Environ. Earth Sci. 2015, 73, 4939–4946. [Google Scholar] [CrossRef]
  95. Lee, H.; Lee, E.; Lee, C.H.; Lee, K. Degradation of chlorotetracycline and bacterial disinfection in livestock wastewater by ozone-based advanced oxidation. J. Ind. Eng. Chem. 2011, 17, 468–473. [Google Scholar] [CrossRef]
  96. Luu, H.T.; Minh, D.N.; Lee, K. Effects of advanced oxidation of penicillin on biotoxicity, biodegradability and subsequent biological treatment. Appl. Chem. Eng. 2018, 29, 690–695. [Google Scholar]
  97. Moradi, M.; Moussavi, G. Investigation of chemical-less UVC/VUV process for advanced oxidation of sulfamethoxazole in aqueous solutions: Evaluation of operational variables and degradation mechanism. Sep. Purif. Technol. 2018, 190, 90–99. [Google Scholar] [CrossRef]
  98. Adams, C.; Wang, Y.; Loftin, K.; Meyer, M. Removal of antibiotics from surface and distilled water in conventional water treatment processes. J. Environ. Eng. 2002, 128, 253–260. [Google Scholar] [CrossRef]
  99. Yuan, F.; Hu, C.; Hu, X.; Wei, D.; Chen, Y.; Qu, J. Photodegradation and toxicity changes of antibiotics in UV and UV/H2O2 process. J. Hazard. Mater. 2011, 185, 1256–1263. [Google Scholar] [CrossRef]
  100. Jiao, S.; Zheng, S.; Yin, D.; Wang, L.; Chen, L. Aqueous photolysis of tetracycline and toxicity of photolytic products to luminescent bacteria. Chemosphere 2008, 73, 377–382. [Google Scholar] [CrossRef]
  101. Baxendale, J.H.; Wilson, J.A. The photolysis of hydrogen peroxide at high light intensities. Trans. Faraday Soc. 1957, 53, 344–356. [Google Scholar] [CrossRef]
  102. Goldstein, S.; Aschengrau, D.; Diamant, Y.; Rabani, J. Photolysis of Aqueous H2O2:  Quantum Yield and Applications for Polychromatic UV Actinometry in Photoreactors. Environ. Sci. Technol. 2007, 41, 7486–7490. [Google Scholar] [CrossRef]
  103. Cédat, B.; De Brauer, C.; Métivier, H.; Dumont, N.; Tutundjan, R. Are UV photolysis and UV/H2O2 process efficient to treat estrogens in waters? Chemical and biological assessment at pilot scale. Water Res. 2016, 100, 357–366. [Google Scholar] [CrossRef]
  104. Ross, F.; Ross, A.B. Selected specific rates of reactions of transients from water in aqueous solution. iii. hydroxyl radical and perhydroxyl radical and their radical ions. Natl. Bur. Stand. Natl. Stand. Ref. Data Ser. 1977. [Google Scholar] [CrossRef]
  105. Bielski, B.H.J.; Cabelli, D.E.; Arudi, R.L.; Ross, A.B. Reactivity of HO2/O2 Radicals in Aqueous Solution. J. Phys. Chem. Ref. Data 1985, 14, 1041–1100. [Google Scholar] [CrossRef]
  106. Christensen, H.; Sehested, K.; Corfitzen, H. Reactions of hydroxyl radicals with hydrogen peroxide at ambient and elevated temperatures. J. Phys. Chem. 1982, 86, 1588–1590. [Google Scholar] [CrossRef]
  107. Jung, Y.J.; Kim, W.G.; Yoon, Y.; Kang, J.W.; Hong, Y.M.; Kim, H.W. Removal of amoxicillin by UV and UV/H2O2 processes. Sci. Total Environ. 2012, 420, 160–167. [Google Scholar] [CrossRef] [PubMed]
  108. Sun, Y.; Cho, D.W.; Graham, N.J.D.; Hou, D.; Yip, A.C.K.; Khan, E.; Song, H.; Li, Y.; Tsang, D.C.W. Degradation of antibiotics by modified vacuum-UV based processes: Mechanistic consequences of H2O2 and K2S2O8 in the presence of halide ions. Sci. Total Environ. 2019, 664, 312–321. [Google Scholar] [CrossRef]
  109. Khorsandi, H.; Teymori, M.; Aghapour, A.A.; Jafari, S.J.; Taghipour, S.; Bargeshadi, R. Photodegradation of ceftriaxone in aqueous solution by using UVC and UVC/H2O2 oxidation processes. Appl. Water Sci. 2019, 9, 81. [Google Scholar] [CrossRef] [Green Version]
  110. De Souza Santos, L.V.; Meireles, A.M.; Lange, L.C. Degradation of antibiotics norfloxacin by Fenton, UV and UV/H2O2. J. Environ. Manag. 2015, 154, 8–12. [Google Scholar] [CrossRef]
  111. Urbano, V.R.; Peres, M.S.; Maniero, M.G.; Guimarães, J.R. Abatement and toxicity reduction of antimicrobials by UV/H2O2 process. J. Environ. Manag. 2017, 193, 439–447. [Google Scholar] [CrossRef]
  112. Li, W.; Xu, X.; Lyu, B.; Tang, Y.; Zhang, Y.; Chen, F.; Korshin, G. Degradation of typical macrolide antibiotic roxithromycin by hydroxyl radical: Kinetics, products, and toxicity assessment. Environ. Sci. Pollut. Res. 2019. [Google Scholar] [CrossRef]
  113. Zhang, R.; Yang, Y.; Huang, C.H.; Zhao, L.; Sun, P. Kinetics and modeling of sulfonamide antibiotic degradation in wastewater and human urine by UV/H2O2 and UV/PDS. Water Res. 2016, 103, 283–292. [Google Scholar] [CrossRef]
  114. Lin, C.C.; Wu, M.S. Feasibility of using UV/H2O2 process to degrade sulfamethazine in aqueous solutions in a large photoreactor. J. Photochem. Photobiol. A Chem. 2018, 367, 446–451. [Google Scholar] [CrossRef]
  115. Lekkerkerker-Teunissen, K.; Benotti, M.J.; Snyder, S.A.; Van Dijk, H.C. Transformation of atrazine, carbamazepine, diclofenac and sulfamethoxazole by low and medium pressure UV and UV/H2O2 treatment. Sep. Purif. Technol. 2012, 96, 33–43. [Google Scholar] [CrossRef]
  116. Navalon, S.; Alvaro, M.; Garcia, H. Heterogeneous Fenton catalysts based on clays, silicas and zeolites. Appl. Catal. B Environ. 2010, 99, 1–26. [Google Scholar] [CrossRef]
  117. Minero, C.; Lucchiari, M.; Vione, D.; Maurino, V. Fe(III)-enhanced sonochemical degradation of methylene blue in aqueous solution. Environ. Sci. Technol. 2005, 39, 8936–8942. [Google Scholar] [CrossRef] [PubMed]
  118. Walling, C. Fenton’s Reagent Revisited. Acc. Chem. Res. 1975, 8, 125–131. [Google Scholar] [CrossRef]
  119. Buxton, G.V.; Greenstock, C.L.; Helman, W.P.; Ross, A.B. Critical Review of rate constants for reactions of hydrated electrons, hydrogen atoms and hydroxyl radicals (⋅OH/⋅O−in Aqueous Solution. J. Phys. Chem. Ref. Data 1988, 17, 513–886. [Google Scholar] [CrossRef] [Green Version]
  120. Kulik, N.; Trapido, M.; Goi, A.; Veressinina, Y.; Munter, R. Combined chemical treatment of pharmaceutical effluents from medical ointment production. Chemosphere 2008, 70, 1525–1531. [Google Scholar] [CrossRef]
  121. Ay, F.; Kargi, F. Advanced oxidation of amoxicillin by Fenton’s reagent treatment. J. Hazard. Mater. 2010, 179, 622–627. [Google Scholar] [CrossRef]
  122. Homem, V.; Alves, A.; Santos, L. Amoxicillin degradation at ppb levels by Fenton’s oxidation using design of experiments. Sci. Total Environ. 2010, 408, 6272–6280. [Google Scholar] [CrossRef]
  123. Türkay, G.K.; Kumbur, H. Investigation of amoxicillin removal from aqueous solution by Fenton and photocatalytic oxidation processes. Kuwait J. Sci. 2019, 46, 85–93. [Google Scholar]
  124. Rozas, O.; Contreras, D.; Mondaca, M.A.; Pérez-Moya, M.; Mansilla, H.D. Experimental design of Fenton and photo-Fenton reactions for the treatment of ampicillin solutions. J. Hazard. Mater. 2010, 177, 1025–1030. [Google Scholar] [CrossRef]
  125. Pulicharla, R.; Brar, S.K.; Rouissi, T.; Auger, S.; Drogui, P.; Verma, M.; Surampalli, R.Y. Degradation of chlortetracycline in wastewater sludge by ultrasonication, Fenton oxidation, and ferro-sonication. Ultrason. Sonochem. 2017, 34, 332–342. [Google Scholar] [CrossRef] [PubMed]
  126. Salari, M.; Rakhshandehroo, G.R.; Nikoo, M.R. Degradation of ciprofloxacin antibiotic by Homogeneous Fenton oxidation: Hybrid AHP-PROMETHEE method, optimization, biodegradability improvement and identification of oxidized by-products. Chemosphere 2018, 206, 157–167. [Google Scholar] [CrossRef] [PubMed]
  127. Rakhshandehroo, G.R.; Salari, M.; Nikoo, M.R. Optimization of degradation of ciprofloxacin antibiotic and assessment of degradation products using full factorial experimental design by fenton homogenous process. Glob. Nest J. 2018, 20, 324–332. [Google Scholar]
  128. Gupta, A.; Garg, A. Degradation of ciprofloxacin using Fenton’s oxidation: Effect of operating parameters, identification of oxidized by-products and toxicity assessment. Chemosphere 2018, 193, 1181–1188. [Google Scholar] [CrossRef]
  129. Borghi, A.A.; Silva, M.F.; Al Arni, S.; Converti, A.; Palma, M.S.A. Doxycycline degradation by the oxidative Fenton process. J. Chem. 2015, 2015, 492030. [Google Scholar] [CrossRef]
  130. Rodrigues-Silva, C.; Maniero, M.G.; Rath, S.; Guimarães, J.R. Degradation of flumequine by the Fenton and photo-Fenton processes: Evaluation of residual antimicrobial activity. Sci. Total Environ. 2013, 445–446, 337–346. [Google Scholar] [CrossRef]
  131. Epold, I.; Trapido, M.; Dulova, N. Degradation of levofloxacin in aqueous solutions by Fenton, ferrous ion-activated persulfate and combined Fenton/persulfate systems. Chem. Eng. J. 2015, 279, 452–462. [Google Scholar] [CrossRef]
  132. Wang, S.; Wang, J. Comparative study on sulfamethoxazole degradation by Fenton and Fe(ii)-activated persulfate process. RSC Adv. 2017, 7, 48670–48677. [Google Scholar] [CrossRef] [Green Version]
  133. Wang, S.; Wang, J. Trimethoprim degradation by Fenton and Fe(II)-activated persulfate processes. Chemosphere 2018, 191, 97–105. [Google Scholar] [CrossRef]
  134. Gallard, H.; De Laat, J. Kinetic modelling of Fe(III)/H2O2 oxidation reactions in dilute aqueous solution using atrazine as a model organic compound. Water Res. 2000, 34, 3107–3116. [Google Scholar] [CrossRef]
  135. Neyens, E.; Baeyens, J. A review of classic Fenton’s peroxidation as an advanced oxidation technique. J. Hazard. Mater. 2003, 98, 33–50. [Google Scholar] [CrossRef]
  136. Zhang, N.; Chen, J.; Fang, Z.; Tsang, E.P. Ceria accelerated nanoscale zerovalent iron assisted heterogenous Fenton oxidation of tetracycline. Chem. Eng. J. 2019, 369, 588–599. [Google Scholar] [CrossRef]
  137. Zhuan, R.; Wang, J. Enhanced mineralization of sulfamethoxazole by gamma radiation in the presence of Fe3O4 as Fenton-like catalyst. Environ. Sci. Pollut. Res. 2019, 26, 27712–27725. [Google Scholar] [CrossRef] [PubMed]
  138. Wang, A.; Wang, H.; Deng, H.; Wang, S.; Shi, W.; Yi, Z.; Qiu, R.; Yan, K. Controllable synthesis of mesoporous manganese oxide microsphere efficient for photo-Fenton-like removal of fluoroquinolone antibiotics. Appl. Catal. B Environ. 2019, 248, 298–308. [Google Scholar] [CrossRef]
  139. Hu, Y.; Chen, K.; Li, Y.L.; He, J.Y.; Zhang, K.S.; Liu, T.; Xu, W.; Huang, X.J.; Kong, L.T.; Liu, J.H. Morphology-tunable WMoO nanowire catalysts for the extremely efficient elimination of tetracycline: Kinetics, mechanisms and intermediates. Nanoscale 2019, 11, 1047–1057. [Google Scholar] [CrossRef] [PubMed]
  140. Wang, Q.; Ma, Y.; Xing, S. Comparative study of Cu-based bimetallic oxides for Fenton-like degradation of organic pollutants. Chemosphere 2018, 203, 450–456. [Google Scholar] [CrossRef] [PubMed]
  141. Wang, R.Z.; Huang, D.L.; Liu, Y.G.; Zhang, C.; Lai, C.; Wang, X.; Zeng, G.M.; Gong, X.M.; Duan, A.; Zhang, Q.; et al. Recent advances in biochar-based catalysts: Properties, applications and mechanisms for pollution remediation. Chem. Eng. J. 2019, 371, 380–403. [Google Scholar] [CrossRef]
  142. Xu, L.; Yang, Y.; Li, W.; Tao, Y.; Sui, Z.; Song, S.; Yang, J. Three-dimensional macroporous graphene-wrapped zero-valent copper nanoparticles as efficient micro-electrolysis-promoted Fenton-like catalysts for metronidazole removal. Sci. Total Environ. 2019, 658, 219–233. [Google Scholar] [CrossRef]
  143. Zha, S.; Cheng, Y.; Gao, Y.; Chen, Z.; Megharaj, M.; Naidu, R. Nanoscale zero-valent iron as a catalyst for heterogeneous Fenton oxidation of amoxicillin. Chem. Eng. J. 2014, 255, 141–148. [Google Scholar] [CrossRef]
  144. Mondal, S.K.; Saha, A.K.; Sinha, A. Removal of ciprofloxacin using modified advanced oxidation processes: Kinetics, pathways and process optimization. J. Clean. Prod. 2018, 171, 1203–1214. [Google Scholar] [CrossRef]
  145. Li, J.; Pan, L.; Yu, G.; Xie, S.; Li, C.; Lai, D.; Li, Z.; You, F.; Wang, Y. The synthesis of heterogeneous Fenton-like catalyst using sewage sludge biochar and its application for ciprofloxacin degradation. Sci. Total Environ. 2019, 654, 1284–1292. [Google Scholar] [CrossRef] [PubMed]
  146. Fang, Z.; Chen, J.; Qiu, X.; Qiu, X.; Cheng, W.; Zhu, L. Effective removal of antibiotic metronidazole from water by nanoscale zero-valent iron particles. Desalination 2011, 268, 60–67. [Google Scholar] [CrossRef]
  147. Huang, D.; Luo, H.; Zhang, C.; Zeng, G.; Lai, C.; Cheng, M.; Wang, R.; Deng, R.; Xue, W.; Gong, X.; et al. Nonnegligible role of biomass types and its compositions on the formation of persistent free radicals in biochar: Insight into the influences on Fenton-like process. Chem. Eng. J. 2019, 361, 353–363. [Google Scholar] [CrossRef]
  148. Zhuang, Y.; Liu, Q.; Kong, Y.; Shen, C.; Hao, H.; Dionysiou, D.D.; Shi, B. Enhanced antibiotic removal through a dual-reaction-center Fenton-like process in 3D graphene based hydrogels. Environ. Sci. Nano 2019, 6, 388–398. [Google Scholar] [CrossRef]
  149. Sedlak, D.L.; Andren, A.W. Oxidation of chlorobenzene with Fenton’s reagent. Environ. Sci. Technol. 1991, 25, 777–782. [Google Scholar] [CrossRef]
  150. Pignatello, J.J. Dark and photoassisted iron(3+)-catalyzed degradation of chlorophenoxy herbicides by hydrogen peroxide. Environ. Sci. Technol. 1992, 26, 944–951. [Google Scholar] [CrossRef]
  151. Bossmann, S.H.; Oliveros, E.; Göb, S.; Siegwart, S.; Dahlen, E.P.; Payawan, L.; Straub, M.; Wörner, M.; Braun, A.M. New Evidence against Hydroxyl Radicals as Reactive Intermediates in the Thermal and Photochemically Enhanced Fenton Reactions. J. Phys. Chem. A 1998, 102, 5542–5550. [Google Scholar] [CrossRef]
  152. Hinojosa Guerra, M.M.; Oller Alberola, I.; Malato Rodriguez, S.; Agüera López, A.; Acevedo Merino, A.; Quiroga Alonso, J.M. Oxidation mechanisms of amoxicillin and paracetamol in the photo-Fenton solar process. Water Res. 2019, 156, 232–240. [Google Scholar] [CrossRef]
  153. Ioannou-Ttofa, L.; Raj, S.; Prakash, H.; Fatta-Kassinos, D. Solar photo-Fenton oxidation for the removal of ampicillin, total cultivable and resistant E. coli and ecotoxicity from secondary-treated wastewater effluents. Chem. Eng. J. 2019, 355, 91–102. [Google Scholar] [CrossRef]
  154. Amildon Ricardo, I.; Paiva, V.A.B.; Paniagua, C.E.S.; Trovó, A.G. Chloramphenicol photo-Fenton degradation and toxicity changes in both surface water and a tertiary effluent from a municipal wastewater treatment plant at near-neutral conditions. Chem. Eng. J. 2018, 347, 763–770. [Google Scholar] [CrossRef]
  155. Giri, A.S.; Golder, A.K. Ciprofloxacin degradation in photo-Fenton and photo-catalytic processes: Degradation mechanisms and iron chelation. J. Environ. Sci. 2019, 80, 82–92. [Google Scholar] [CrossRef] [PubMed]
  156. Giraldo-Aguirre, A.L.; Serna-Galvis, E.A.; Erazo-Erazo, E.D.; Silva-Agredo, J.; Giraldo-Ospina, H.; Flórez-Acosta, O.A.; Torres-Palma, R.A. Removal of β-lactam antibiotics from pharmaceutical wastewaters using photo-Fenton process at near-neutral pH. Environ. Sci. Pollut. Res. 2018, 25, 20293–20303. [Google Scholar] [CrossRef] [PubMed]
  157. Wang, Q.; Pang, W.; Mao, Y.; Sun, Q.; Zhang, P.; Ke, Q.; Yu, H.; Dai, C.; Zhao, M. Study of the degradation of trimethoprim using photo-Fenton oxidation technology. Water 2019, 11, 207. [Google Scholar] [CrossRef] [Green Version]
  158. Gogate, P.R.; Pandit, A.B. A review of imperative technologies for wastewater treatment I: Oxidation technologies at ambient conditions. Adv. Environ. Res. 2004, 8, 501–551. [Google Scholar] [CrossRef]
  159. Gogate, P.R.; Pandit, A.B. A review of imperative technologies for wastewater treatment II: Hybrid methods. Adv. Environ. Res. 2004, 8, 553–597. [Google Scholar] [CrossRef]
  160. Pirkanniemi, K.; Sillanpää, M. Heterogeneous water phase catalysis as an environmental application: A review. Chemosphere 2002, 48, 1047–1060. [Google Scholar] [CrossRef]
  161. Wang, N.; Zheng, T.; Zhang, G.; Wang, P. A review on Fenton-like processes for organic wastewater treatment. J. Environ. Chem. Eng. 2016, 4, 762–787. [Google Scholar] [CrossRef] [Green Version]
  162. Hao, H.; Shi, J.L.; Xu, H.; Li, X.; Lang, X. N-hydroxyphthalimide-TiO2 complex visible light photocatalysis. Appl. Catal. B Environ. 2019, 246, 149–155. [Google Scholar] [CrossRef]
  163. Méndez-Medrano, M.G.; Kowalska, E.; Lehoux, A.; Herissan, A.; Ohtani, B.; Bahena, D.; Briois, V.; Colbeau-Justin, C.; Rodríguez-López, J.L.; Remita, H. Surface Modification of TiO2 with Ag Nanoparticles and CuO Nanoclusters for Application in Photocatalysis. J. Phys. Chem. C 2016, 120, 5143–5154. [Google Scholar] [CrossRef]
  164. Sanzone, G.; Zimbone, M.; Cacciato, G.; Ruffino, F.; Carles, R.; Privitera, V.; Grimaldi, M.G. Ag/TiO2 nanocomposite for visible light-driven photocatalysis. Superlattices Microstruct. 2018, 123, 394–402. [Google Scholar] [CrossRef]
  165. Xiong, X.; Xu, Y. Synergetic Effect of Pt and Borate on the TiO2-Photocatalyzed Degradation of Phenol in Water. J. Phys. Chem. C 2016, 120, 3906–3912. [Google Scholar] [CrossRef]
  166. Wang, D.; Wang, S.; Li, B.; Zhang, Z.; Zhang, Q. Tunable band gap of NV co-doped Ca:TiO2B (CaTi5O11) for visible-light photocatalysis. Int. J. Hydrogen Energy 2019, 44, 4716–4723. [Google Scholar] [CrossRef]
  167. Du, D.; Shi, W.; Wang, L.; Zhang, J. Yolk-shell structured Fe3O4@void@TiO2 as a photo-Fenton-like catalyst for the extremely efficient elimination of tetracycline. Appl. Catal. B Environ. 2017, 200, 484–492. [Google Scholar] [CrossRef]
  168. Gurkan, Y.Y.; Kasapbasi, E.; Cinar, Z. Enhanced solar photocatalytic activity of TiO2 by selenium(IV) ion-doping: Characterization and DFT modeling of the surface. Chem. Eng. J. 2013, 214, 34–44. [Google Scholar] [CrossRef]
  169. Eswar, N.K.; Ramamurthy, P.C.; Madras, G. Novel synergistic photocatalytic degradation of antibiotics and bacteria using V–N doped TiO2 under visible light: The state of nitrogen in V-doped TiO2. New J. Chem. 2016, 40, 3464–3475. [Google Scholar] [CrossRef]
  170. Zheng, X.; Xu, S.; Wang, Y.; Sun, X.; Gao, Y.; Gao, B. Enhanced degradation of ciprofloxacin by graphitized mesoporous carbon (GMC)-TiO2 nanocomposite: Strong synergy of adsorption-photocatalysis and antibiotics degradation mechanism. J. Colloid Interface Sci. 2018, 527, 202–213. [Google Scholar] [CrossRef]
  171. Serna-Galvis, E.A.; Giraldo-Aguirre, A.L.; Silva-Agredo, J.; Flórez-Acosta, O.A.; Torres-Palma, R.A. Removal of antibiotic cloxacillin by means of electrochemical oxidation, TiO2 photocatalysis, and photo-Fenton processes: Analysis of degradation pathways and effect of the water matrix on the elimination of antimicrobial activity. Environ. Sci. Pollut. Res. 2017, 24, 6339–6352. [Google Scholar] [CrossRef]
  172. Tran, M.L.; Fu, C.C.; Juang, R.S. Effects of water matrix components on degradation efficiency and pathways of antibiotic metronidazole by UV/TiO2 photocatalysis. J. Mol. Liq. 2019, 276, 32–38. [Google Scholar] [CrossRef]
  173. Shankaraiah, G.; Poodari, S.; Bhagawan, D.; Himabindu, V.; Vidyavathi, S. Degradation of antibiotic norfloxacin in aqueous solution using advanced oxidation processes (AOPs)—A comparative study. Desalin. Water Treat. 2016, 57, 27804–27815. [Google Scholar] [CrossRef]
  174. Serna-Galvis, E.A.; Silva-Agredo, J.; Giraldo, A.L.; Flórez-Acosta, O.A.; Torres-Palma, R.A. Comparative study of the effect of pharmaceutical additives on the elimination of antibiotic activity during the treatment of oxacillin in water by the photo-Fenton, TiO2-photocatalysis and electrochemical processes. Sci. Total Environ. 2016, 541, 1431–1438. [Google Scholar] [CrossRef] [Green Version]
  175. Jiang, Q.; Zhu, R.; Zhu, Y.; Chen, Q. Efficient degradation of cefotaxime by a UV+ferrihydrite/TiO2+H2O2 process: The important role of ferrihydrite in transferring photo-generated electrons from TiO2 to H2O2. J. Chem. Technol. Biotechnol. 2019, 94, 2512–2521. [Google Scholar] [CrossRef]
  176. García-Muñoz, P.; Zussblatt, N.P.; Pliego, G.; Zazo, J.A.; Fresno, F.; Chmelka, B.F.; Casas, J.A. Evaluation of photoassisted treatments for norfloxacin removal in water using mesoporous Fe2O3-TiO2 materials. J. Environ. Manag. 2019, 238, 243–250. [Google Scholar] [CrossRef] [PubMed]
  177. Pokhrel, N.; Vabbina, P.K.; Pala, N. Sonochemistry: Science and Engineering. Ultrason. Sonochem. 2016, 29, 104–128. [Google Scholar] [CrossRef] [PubMed]
  178. González-García, J.; Sáez, V.; Tudela, I.; Díez-Garcia, M.I.; Deseada Esclapez, M.; Louisnard, O. Sonochemical Treatment of Water Polluted by Chlorinated Organocompounds. A Review. Water 2010, 2, 28–74. [Google Scholar] [CrossRef]
  179. Hao, H.; Chen, Y.; Wu, M.; Wang, H.; Yin, Y.; Lü, Z. Sonochemistry of degrading p-chlorophenol in water by high frequency ultrasound. Ultrason. Sonochem. 2004, 11, 43–46. [Google Scholar] [CrossRef]
  180. Sathishkumar, P.; Mangalaraja, R.V.; Anandan, S. Review on the recent improvements in sonochemical and combined sonochemical oxidation processes—A powerful tool for destruction of environmental contaminants. Renew. Sustain. Energy Rev. 2016, 55, 426–454. [Google Scholar] [CrossRef]
  181. Serna-Galvis, E.A.; Botero-Coy, A.M.; Martínez-Pachón, D.; Moncayo-Lasso, A.; Ibáñez, M.; Hernández, F.; Torres-Palma, R.A. Degradation of seventeen contaminants of emerging concern in municipal wastewater effluents by sonochemical advanced oxidation processes. Water Res. 2019, 154, 349–360. [Google Scholar] [CrossRef]
  182. Bagal, M.V.; Gogate, P.R. Wastewater treatment using hybrid treatment schemes based on cavitation and Fenton chemistry: A review. Ultrason. Sonochem. 2014, 21, 1–14. [Google Scholar] [CrossRef]
  183. Dindarsafa, M.; Khataee, A.; Kaymak, B.; Vahid, B.; Karimi, A.; Rahmani, A. Heterogeneous sono-Fenton-like process using martite nanocatalyst prepared by high energy planetary ball milling for treatment of a textile dye. Ultrason. Sonochem. 2017, 34, 389–399. [Google Scholar] [CrossRef]
  184. Zhou, T.; Wu, X.; Zhang, Y.; Li, J.; Lim, T.T. Synergistic catalytic degradation of antibiotic sulfamethazine in a heterogeneous sonophotolytic goethite/oxalate Fenton-like system. Appl. Catal. B Environ. 2013, 136-137, 294–301. [Google Scholar] [CrossRef]
  185. Ghoreishian, S.M.; Raju, G.S.R.; Pavitra, E.; Kwak, C.H.; Han, Y.K.; Huh, Y.S. Ultrasound-assisted heterogeneous degradation of tetracycline over flower-like rGO/CdWO4 hierarchical structures as robust solar-light-responsive photocatalysts: Optimization, kinetics, and mechanism. Appl. Surf. Sci. 2019, 489, 110–122. [Google Scholar] [CrossRef]
  186. Vinesh, V.; Shaheer, A.R.M.; Neppolian, B. Reduced graphene oxide (rGO) supported electron deficient B-doped TiO2 (Au/B-TiO2/rGO) nanocomposite: An efficient visible light sonophotocatalyst for the degradation of Tetracycline (TC). Ultrason. Sonochem. 2019, 50, 302–310. [Google Scholar] [CrossRef] [PubMed]
  187. Abazari, R.; Mahjoub, A.R.; Sanati, S.; Rezvani, Z.; Hou, Z.; Dai, H. Ni-Ti Layered Double Hydroxide@Graphitic Carbon Nitride Nanosheet: A Novel Nanocomposite with High and Ultrafast Sonophotocatalytic Performance for Degradation of Antibiotics. Inorg. Chem. 2019, 58, 1834–1849. [Google Scholar] [CrossRef] [PubMed]
  188. Brillas, E.; Baños, M.Á.; Skoumal, M.; Cabot, P.L.; Garrido, J.A.; Rodríguez, R.M. Degradation of the herbicide 2,4-DP by anodic oxidation, electro-Fenton and photoelectro-Fenton using platinum and boron-doped diamond anodes. Chemosphere 2007, 68, 199–209. [Google Scholar] [CrossRef] [PubMed]
  189. Mirzaei, S.; Javanbakht, V. Dye removal from aqueous solution by a novel dual cross-linked biocomposite obtained from mucilage of Plantago Psyllium and eggshell membrane. Int. J. Biol. Macromol. 2019, 134, 1187–1204. [Google Scholar] [CrossRef]
  190. Panizza, M.; Delucchi, M.; Cerisola, G. Electrochemical degradation of anionic surfactants. J. Appl. Electrochem. 2005, 35, 357–361. [Google Scholar] [CrossRef]
  191. Panizza, M.; Cerisola, G. Direct And Mediated Anodic Oxidation of Organic Pollutants. Chem. Rev. 2009, 109, 6541–6569. [Google Scholar] [CrossRef]
  192. Cañizares, P.; Sáez, C.; Sánchez-Carretero, A.; Rodrigo, M.A. Synthesis of novel oxidants by electrochemical technology. J. Appl. Electrochem. 2009, 39, 2143. [Google Scholar] [CrossRef]
  193. Rodrigo, M.A.; Cañizares, P.; Sánchez-Carretero, A.; Sáez, C. Use of conductive-diamond electrochemical oxidation for wastewater treatment. Catal. Today 2010, 151, 173–177. [Google Scholar] [CrossRef]
  194. Cañizares, P.; Sáez, C.; Sánchez-Carretero, A.; Rodrigo, M.A. Influence of the characteristics of p-Si BDD anodes on the efficiency of peroxodiphosphate electrosynthesis process. Electrochem. Commun. 2008, 10, 602–606. [Google Scholar] [CrossRef]
  195. Comninellis, C. Electrocatalysis in the electrochemical conversion/combustion of organic pollutants for waste water treatment. Electrochim. Acta 1994, 39, 1857–1862. [Google Scholar] [CrossRef]
  196. Waterston, K.; Wang, J.W.; Bejan, D.; Bunce, N.J. Electrochemical waste water treatment: Electrooxidation of acetaminophen. J. Appl. Electrochem. 2006, 36, 227–232. [Google Scholar] [CrossRef]
  197. Yosypchuk, O.; Barek, J.; Vyskočil, V. Voltammetric Determination of Carcinogenic Derivatives of Pyrene Using a Boron-Doped Diamond Film Electrode. Anal. Lett. 2012, 45, 449–459. [Google Scholar] [CrossRef]
  198. Lima, A.B.; Faria, E.O.; Montes, R.H.O.; Cunha, R.R.; Richter, E.M.; Munoz, R.A.A.; dos Santos, W.T.P. Electrochemical Oxidation of Ibuprofen and Its Voltammetric Determination at a Boron-Doped Diamond Electrode. Electroanalysis 2013, 25, 1585–1588. [Google Scholar] [CrossRef]
  199. Pereira, P.F.; Marra, M.C.; Lima, A.B.; Dos Santos, W.T.P.; Munoz, R.A.A.; Richter, E.M. Fast and simultaneous determination of nimesulide and paracetamol by batch injection analysis with amperometric detection on bare boron-doped diamond electrode. Diam. Relat. Mater. 2013, 39, 41–46. [Google Scholar] [CrossRef]
  200. Sun, H.; Dong, L.; Yu, H.; Huo, M. Direct electrochemical oxidation and detection of hydrazine on a boron doped diamond (BDD) electrode. Russ. J. Electrochem. 2013, 49, 883–887. [Google Scholar] [CrossRef]
  201. Zou, Y.S.; He, L.L.; Zhang, Y.C.; Shi, X.Q.; Li, Z.X.; Zhou, Y.L.; Tu, C.J.; Gu, L.; Zeng, H.B. The microstructure and electrochemical properties of boron-doped nanocrystalline diamond film electrodes and their application in non-enzymatic glucose detection. J. Appl. Electrochem. 2013, 43, 911–917. [Google Scholar] [CrossRef]
  202. Marselli, B.; Garcia-Gomez, J.; Michaud, P.A.; Rodrigo, M.A.; Comninellis, C. Electrogeneration of hydroxyl radicals on boron-doped diamond electrodes. J. Electrochem. Soc. 2003, 150, D79–D83. [Google Scholar] [CrossRef]
  203. Sun, J.; Lu, H.; Du, L.; Lin, H.; Li, H. Anodic oxidation of anthraquinone dye Alizarin Red S at Ti/BDD electrodes. Appl. Surf. Sci. 2011, 257, 6667–6671. [Google Scholar] [CrossRef]
  204. Migliorini, F.L.; Braga, N.A.; Alves, S.A.; Lanza, M.R.V.; Baldan, M.R.; Ferreira, N.G. Anodic oxidation of wastewater containing the Reactive Orange 16 Dye using heavily boron-doped diamond electrodes. J. Hazard. Mater. 2011, 192, 1683–1689. [Google Scholar] [CrossRef]
  205. Iniesta, J.; Michaud, P.A.; Panizza, M.; Cerisola, G.; Aldaz, A.; Comninellis, C. Electrochemical oxidation of phenol at boron-doped diamond electrode. Electrochim. Acta 2001, 46, 3573–3578. [Google Scholar] [CrossRef]
  206. Hupert, M.; Muck, A.; Wang, J.; Stotter, J.; Cvackova, Z.; Haymond, S.; Show, Y.; Swain, G.M. Conductive diamond thin-films in electrochemistry. Diam. Relat. Mater. 2003, 12, 1940–1949. [Google Scholar] [CrossRef]
  207. Boye, B.; Brillas, E.; Marselli, B.; Michaud, P.A.; Comninellis, C.; Farnia, G.; Sandonà, G. Electrochemical incineration of chloromethylphenoxy herbicides in acid medium by anodic oxidation with boron-doped diamond electrode. Electrochim. Acta 2006, 51, 2872–2880. [Google Scholar] [CrossRef]
  208. Cañizares, P.; Gadri, A.; Lobato, J.; Nasr, B.; Paz, R.; Rodrigo, M.A.; Saez, C. Electrochemical Oxidation of Azoic Dyes with Conductive-Diamond Anodes. Ind. Eng. Chem. Res. 2006, 45, 3468–3473. [Google Scholar] [CrossRef]
  209. Oturan, N.; Hamza, M.; Ammar, S.; Abdelhédi, R.; Oturan, M.A. Oxidation/mineralization of 2-Nitrophenol in aqueous medium by electrochemical advanced oxidation processes using Pt/carbon-felt and BDD/carbon-felt cells. J. Electroanal. Chem. 2011, 661, 66–71. [Google Scholar] [CrossRef]
  210. El-Ghenymy, A.; Arias, C.; Cabot, P.L.; Centellas, F.; Garrido, J.A.; Rodríguez, R.M.; Brillas, E. Electrochemical incineration of sulfanilic acid at a boron-doped diamond anode. Chemosphere 2012, 87, 1126–1133. [Google Scholar] [CrossRef]
  211. Cavalcanti, E.B.; Segura, S.G.; Centellas, F.; Brillas, E. Electrochemical incineration of omeprazole in neutral aqueous medium using a platinum or boron-doped diamond anode: Degradation kinetics and oxidation products. Water Res. 2013, 47, 1803–1815. [Google Scholar] [CrossRef]
  212. Rabaaoui, N.; Moussaoui, Y.; Allagui, M.S.; Ahmed, B.; Elaloui, E. Anodic oxidation of nitrobenzene on BDD electrode: Variable effects and mechanisms of degradation. Sep. Purif. Technol. 2013, 107, 318–323. [Google Scholar] [CrossRef]
  213. Sales Solano, A.M.; Costa De Araújo, C.K.; Vieira De Melo, J.; Peralta-Hernandez, J.M.; Ribeiro Da Silva, D.; Martínez-Huitle, C.A. Decontamination of real textile industrial effluent by strong oxidant species electrogenerated on diamond electrode: Viability and disadvantages of this electrochemical technology. Appl. Catal. B Environ. 2013, 130, 112–120. [Google Scholar] [CrossRef]
  214. Flox, C.; Cabot, P.L.; Centellas, F.; Garrido, J.A.; Rodríguez, R.M.; Arias, C.; Brillas, E. Electrochemical combustion of herbicide mecoprop in aqueous medium using a flow reactor with a boron-doped diamond anode. Chemosphere 2006, 64, 892–902. [Google Scholar] [CrossRef]
  215. Bergmann, M.E.H.; Rollin, J.; Iourtchouk, T. The occurrence of perchlorate during drinking water electrolysis using BDD anodes. Electrochim. Acta 2009, 54, 2102–2107. [Google Scholar] [CrossRef]
  216. Sánchez-Carretero, A.; Sáez, C.; Cañizares, P.; Rodrigo, M.A. Electrochemical production of perchlorates using conductive diamond electrolyses. Chem. Eng. J. 2011, 166, 710–714. [Google Scholar] [CrossRef]
  217. Rodríguez-Chueca, J.; Varella della Giustina, S.; Rocha, J.; Fernandes, T.; Pablos, C.; Encinas, Á.; Barceló, D.; Rodríguez-Mozaz, S.; Manaia, C.M.; Marugán, J. Assessment of full-scale tertiary wastewater treatment by UV-C based-AOPs: Removal or persistence of antibiotics and antibiotic resistance genes? Sci. Total Environ. 2019, 652, 1051–1061. [Google Scholar] [CrossRef] [PubMed]
  218. Chowdhury, P.; Sarathy, S.R.; Das, S.; Li, J.; Ray, A.K.; Ray, M.B. Direct UV photolysis of pharmaceutical compounds: Determination of pH-dependent quantum yield and full-scale performance. Chem. Eng. J. 2020, 380, 122460. [Google Scholar] [CrossRef]
  219. Rame; Tridecima, A.; Pranoto, H. FLASH Technology: Full-Scale Hospital Waste Water Treatments Adopted in Aceh. In Proceedings of the E3S Web of Conferences, Semarang, Indonesia, 15–16 August 2017; Volume 31. [Google Scholar]
  220. Sui, Q.; Huang, J.; Lu, S.; Deng, S.; Wang, B.; Zhao, W.; Qiu, Z.; Yu, G. Removal of pharmaceutical and personal care products by sequential ultraviolet and ozonation process in a full-scale wastewater treatment plant. Front. Environ. Sci. Eng. 2014, 8, 62–68. [Google Scholar] [CrossRef]
  221. Paździor, K.; Bilińska, L.; Ledakowicz, S. A review of the existing and emerging technologies in the combination of AOPs and biological processes in industrial textile wastewater treatment. Chem. Eng. J. 2019, 376, 120597. [Google Scholar] [CrossRef]
  222. Szczuka, A.; Berglund-Brown, J.P.; Chen, H.K.; Quay, A.N.; Mitch, W.A. Evaluation of a Pilot Anaerobic Secondary Effluent for Potable Reuse: Impact of Different Disinfection Schemes on Organic Fouling of RO Membranes and DBP Formation. Environ. Sci. Technol. 2019, 53, 3166–3176. [Google Scholar] [CrossRef]
  223. Miralles-Cuevas, S.; Darowna, D.; Wanag, A.; Mozia, S.; Malato, S.; Oller, I. Comparison of UV/H2O2, UV/S2O82−, solar/Fe(II)/H2O2 and solar/Fe(II)/S2O82− at pilot plant scale for the elimination of micro-contaminants in natural wat. Chem. Eng. J. 2017, 310, 514–524. [Google Scholar] [CrossRef]
  224. Garcia-Segura, S.; Bellotindos, L.M.; Huang, Y.H.; Brillas, E.; Lu, M.C. Fluidized-bed Fenton process as alternative wastewater treatment technology—A review. J. Taiwan Inst. Chem. Eng. 2016, 67, 211–225. [Google Scholar] [CrossRef]
  225. Hamza, R.A.; Iorhemen, O.T.; Tay, J.H. Occurrence, impacts and removal of emerging substances of concern from wastewater. Environ. Technol. Innov. 2016, 5, 161–175. [Google Scholar] [CrossRef]
  226. De Araújo, K.S.; Antonelli, R.; Gaydeczka, B.; Granato, A.C.; Malpass, G.R.P.; Garcia-Segura, S.; Bellotindos, L.M.; Huang, Y.H.; Brillas, E.; Lu, M.C.; et al. Advanced oxidation processes for antibiotics removal: A review. Chem. Eng. J. 2016, 46, 211–225. [Google Scholar]
  227. Michael, I.; Hapeshi, E.; Michael, C.; Varela, A.R.; Kyriakou, S.; Manaia, C.M.; Fatta-Kassinos, D. Solar photo-Fenton process on the abatement of antibiotics at a pilot scale: Degradation kinetics, ecotoxicity and phytotoxicity assessment and removal of antibiotic resistant enterococci. Water Res. 2012, 46, 5621–5634. [Google Scholar] [CrossRef]
  228. Matsushita, T.; Honda, S.; Kuriyama, T.; Fujita, Y.; Kondo, T.; Matsui, Y.; Shirasaki, N.; Takanashi, H.; Kameya, T. Identification of mutagenic transformation products generated during oxidation of 3-methyl-4-nitrophenol solutions by orbitrap tandem mass spectrometry and quantitative structure–activity relationship analyses. Water Res. 2018, 129, 347–356. [Google Scholar] [CrossRef] [Green Version]
  229. Tišler, T.; Pintar, A. Evolution of Toxicity and Estrogenic Activity Throughout AOP’s Surface and Drinking Water Treatment BT—Applications of Advanced Oxidation Processes (AOPs) in Drinking Water Treatment; En; Gil, A., Galeano, L.A., Vicente, M.Á., Eds.; Springer International Publishing: Cham, Switzerland, 2019; pp. 387–403. ISBN 978-3-319-76882-3. [Google Scholar]
  230. Arvai, A.; Jasim, S.; Biswas, N. Bromate Formation in Ozone and Advanced Oxidation Processes. Ozone Sci. Eng. 2012, 34, 325–333. [Google Scholar] [CrossRef]
  231. Bourgin, M.; Beck, B.; Boehler, M.; Borowska, E.; Fleiner, J.; Salhi, E.; Teichler, R.; von Gunten, U.; Siegrist, H.; McArdell, C.S. Evaluation of a full-scale wastewater treatment plant upgraded with ozonation and biological post-treatments: Abatement of micropollutants, formation of transformation products and oxidation by-products. Water Res. 2018, 129, 486–498. [Google Scholar] [CrossRef]
  232. Bourgin, M.; Borowska, E.; Helbing, J.; Hollender, J.; Kaiser, H.-P.; Kienle, C.; McArdell, C.S.; Simon, E.; von Gunten, U. Effect of operational and water quality parameters on conventional ozonation and the advanced oxidation process O3/H2O2: Kinetics of micropollutant abatement, transformation product and bromate formation in a surface water. Water Res. 2017, 122, 234–245. [Google Scholar] [CrossRef] [Green Version]
  233. Semitsoglou-Tsiapou, S.; Templeton, M.R.; Graham, N.J.D.; Mandal, S.; Hernández Leal, L.; Kruithof, J.C. Potential formation of mutagenicity by low pressure-UV/H2O2 during the treatment of nitrate-rich source waters. Environ. Sci. Water Res. Technol. 2018, 4, 1252–1261. [Google Scholar] [CrossRef]
  234. Sharma, A.; Ahmad, J.; Flora, S.J.S. Application of advanced oxidation processes and toxicity assessment of transformation products. Environ. Res. 2018, 167, 223–233. [Google Scholar] [CrossRef]
  235. Lai, W.W.P.; Hsu, M.H.; Lin, A.Y.C. The role of bicarbonate anions in methotrexate degradation via UV/TiO2: Mechanisms, reactivity and increased toxicity. Water Res. 2017, 112, 157–166. [Google Scholar] [CrossRef]
  236. Magdeburg, A.; Stalter, D.; Oehlmann, J. Whole effluent toxicity assessment at a wastewater treatment plant upgraded with a full-scale post-ozonation using aquatic key species. Chemosphere 2012, 88, 1008–1014. [Google Scholar] [CrossRef]
  237. Li, X.; Shi, H.; Li, K.; Zhang, L. Combined process of biofiltration and ozone oxidation as an advanced treatment process for wastewater reuse. Front. Environ. Sci. Eng. 2015, 9, 1076–1083. [Google Scholar] [CrossRef]
  238. Dantas, R.F.; Rossiter, O.; Teixeira, A.K.R.; Simões, A.S.M.; Da Silva, V.L. Direct UV photolysis of propranolol and metronidazole in aqueous solution. Chem. Eng. J. 2010, 158, 143–147. [Google Scholar] [CrossRef]
  239. Chan, S.H.S.; Wu, T.Y.; Juan, J.C.; Teh, C.Y. Recent developments of metal oxide semiconductors as photocatalysts in advanced oxidation processes (AOPs) for treatment of dye waste-water. J. Chem. Technol. Biotechnol. 2011, 86, 1130–1158. [Google Scholar] [CrossRef]
  240. Lv, Y.; Yu, L.; Huang, H.; Liu, H.; Feng, Y. Preparation, characterization of P-doped TiO2 nanoparticles and their excellent photocatalystic properties under the solar light irradiation. J. Alloys Compd. 2009, 488, 314–319. [Google Scholar] [CrossRef]
  241. Hamadanian, M.; Reisi-Vanani, A.; Majedi, A. Synthesis, characterization and effect of calcination temperature on phase transformation and photocatalytic activity of Cu, S-codoped TiO2 nanoparticles. Appl. Surf. Sci. 2010, 256, 1837–1844. [Google Scholar] [CrossRef]
  242. Janus, M.; Choina, J.; Morawski, A.W. Azo dyes decomposition on new nitrogen-modified anatase TiO2 with high adsorptivity. J. Hazard. Mater. 2009, 166, 1–5. [Google Scholar] [CrossRef]
  243. Liu, Y.; Zeng, X.; Hu, X.; Hu, J.; Zhang, X. Two-dimensional nanomaterials for photocatalytic water disinfection: Recent progress and future challenges. J. Chem. Technol. Biotechnol. 2019, 94, 22–37. [Google Scholar] [CrossRef] [Green Version]
  244. Lai, C.; Wang, M.M.; Zeng, G.M.; Liu, Y.G.; Huang, D.L.; Zhang, C.; Wang, R.Z.; Xu, P.; Cheng, M.; Huang, C.; et al. Synthesis of surface molecular imprinted TiO2/graphene photocatalyst and its highly efficient photocatalytic degradation of target pollutant under visible light irradiation. Appl. Surf. Sci. 2016, 390, 368–376. [Google Scholar] [CrossRef]
  245. Tisa, F.; Abdul Raman, A.A.; Wan Daud, W.M.A. Applicability of fluidized bed reactor in recalcitrant compound degradation through advanced oxidation processes: A review. J. Environ. Manag. 2014, 146, 260–275. [Google Scholar] [CrossRef]
  246. Briones, R.M.; De Luna, M.D.G.; Lu, M.C. Optimization of acetaminophen degradation by fluidized-bed Fenton process. Desalin. Water Treat. 2012, 45, 100–111. [Google Scholar] [CrossRef]
  247. Anotai, J.; Sakulkittimasak, P.; Boonrattanakij, N.; Lu, M.C. Kinetics of nitrobenzene oxidation and iron crystallization in fluidized-bed Fenton process. J. Hazard. Mater. 2009, 165, 874–880. [Google Scholar] [CrossRef] [PubMed]
Table 1. Advantages and disadvantages of the different kinds of water treatments.
Table 1. Advantages and disadvantages of the different kinds of water treatments.
Physical or Physicochemical TreatmentBiological TreatmentChemical Treatment
Kind of pollutantIndustrial (organic, inorganic, metals)Industrial and domestic (low concentrations of organic and some inorganic)Industrial (organic, inorganic, metals)
MethodsFiltration
(Adsorption
(Air flotation
(Extraction
(Flocculation Sedimentation
Anaerobic
(Aerobic
(Activated muds
Thermal oxidation (combustion)
(Chemical oxidation
(Ion exchange
(Chemical precipitation
AdvantagesLow cost of capital
(Relatively safe
(Easy to operate
Easy maintenance Relatively safe elimination of the dissolved contaminants
(Easy to operate
High degree of treatment
(Elimination of the dissolved contaminants
DisadvantagesVolatile emissions
(High energetic cost Complex maintenance
Volatile emissions
(Require elimination of residual muds
(Susceptible to toxins or antibiotics
High costs of capital and operation. Difficult operation
Table 2. Standard reduction potentials in aqueous medium of the most commonly used oxidizing agents.
Table 2. Standard reduction potentials in aqueous medium of the most commonly used oxidizing agents.
OxidizerReduction ReactionE°/V
FluorineF2(g) + 2H+ + 2e → 2HF
F2(g) + 2e → 2F
3.05
Hydroxyl radicalOH + H+ + e → H2O2.80
Sulfate radical anionSO4 +e → SO42−2.60
FerrateFeO42− + 8H+ + 3e → Fe3+ + 4H2O2.20
OzoneO3(g) + 2H+ + 2e → O2(g) + H2O2.08
PeroxodisulfateS2O82− + 2e → 2SO42−2.01
Hydrogen peroxideH2O2 + 2H+ + 2e → 2H2O1.76
Permanganate (a)MnO4 + 4H+ + 3e → MnO2(s) + 2H2O1.67
Hydroperoxyl radical (a)HO2 + 3H+ + 3e → 2H2O1.65
Permanganate (b)MnO4 + 8H+ + 5e → Mn2+ + 4H2O1.51
Hydroperoxiyl radical (b)HO2 + H+ +e → H2O21.44
DichromateCr2O72− + 14H+ + 6e → 2Cr3+ + 7H2O1.36
ChlorineCl2(g) + 2e → 2Cl1.36
Manganese dioxideMnO2 + 4H+ + 2e → Mn2+ + 2H2O1.23
OxygenO2(g) + 4H+ + 4e → 2H2O1.23
BromineBr2(l) + 2e → 2Br1.07
(a) Circumneutral or weakly acidic medium; (b) Strongly acidic medium.
Table 3. A classification of advanced oxidation processes (AOPs) according to the source of ·OH radicals.
Table 3. A classification of advanced oxidation processes (AOPs) according to the source of ·OH radicals.
Generic NameSource of OH Radicals
Advanced Oxidation Processes (AOPs)PhotolysisUV radiation
O3-based processesO3
O3/UV
O3/H2O2
O3/H2O2/UV
H2O2-based processesH2O2/UV
H2O2/Fe2+ (Fenton)
H2O2/Fe3+ (Fenton-like)
H2O2/Fe2+/UV (Photo-Fenton)
Heterogeneous photocatalysisTiO2/UV
TiO2/UV/H2O2
Sonochemical oxidationUltrasounds 20kHz–2MHz (water sonolysis)
Electrochemical oxidationElectricity, 2-20A
((water electrolysis)
Table 4. Removal efficiency of antibiotics in waters by photodegradation.
Table 4. Removal efficiency of antibiotics in waters by photodegradation.
AntibioticMechanismMaximum Removal EfficiencyRemarksReference
Amoxicillin (AMX)
(Ampicillin (AMP)
(Piperacillin (PPR)
(Penicillin V (PNV)
Mainly indirect photolysis~100% AMX & AMP
(~95% PNV
(~90% PPR
Photodegradation by sunlight may play a role in the degradation of these antibiotics together
(with hydrolysis and microbial degradation
[49]
Cefalexin (CFL)
(Cefradine (CFR)
(Cefapirin (CFP)
(Cefazolin (CFZ)
(Cefotaxime (CFT)
Direct photolysis (CFP, CFZ)
(Indirect photolysis (CFL, CFR)
(Direct and indirect photolysis equally (CFT)
86%–89% in all casesPhoto byproducts were found to be less photolabile and more toxic than precursors[50]
Cefradine (CFR)
(Cefuroxime (CFX)
(Ceftriaxone (CFN)
(Cefepime (CFM)
Direct photolysis (CFN);
(Indirect Photolysis (CFR, CFX, CFM)
~90% CFM
(~80% CFX
(~70% CFN
(~60% CFR
Abiotic hydrolysis was responsible for the elimination of the cephalosporins. Direct photolysis significantly stimulated the abiotic degradation[51]
Ceftiofur (CFF)
(Cefapirin (CFP)
Direct photolysis with some pH-dependent hydrolysis~96% CFP
(~92% CFF
Both compounds are relatively stable under neutral and acid environment, whereas base-catalyzed reactions (pH > 9) led to fast degradation[52]
Ciprofloxacin (CPR)Direct photolysis (Photooxidation, defluorination, and cleavage of the piperazine ring)n.a.Fast process, particularly at slightly basic pH[53]
Difloxacin (DFL)
(Sarafloxacin (SRF)
Direct photolysis>99% in both casesSRF is the primary photoproduct of DFL and shows relatively higher persistence[54]
Enofloxacine (ENF)Direct and (some) indirect photolysisVery close to 100%Self-sensitized fluoroquinolone photooxidation
(via ·OH radicals and singlet oxygen also plausible
[55]
Norfloxacin (NRF)
(Ofloxacin (OFX)
(Ciprofloxacin (CPR)
(Enrofloxacin (ENR)
(Sparfloxacin (SPR)
(Danofloxacin (DNF)
(Sulfanilamide (SND)
(Sulfaguanidine (SGD)
(Sulfadiazine (SDZ)
(Sulfamethoxazole (SLF)
(Sulfathiazole (STZ)
(Sulfisoxazole (SFX)
(Sulfamethizole (SMT)
(Sulfamethazine (SMZ)
(Sulfamethoxypyridazine (SMP)
Direct
(photolysis and collateral processes (e.g., hydrolysis)
>98.5% in all casesPhoto byproducts derived from desulfonation and/or denitrification, as well as hydroxylation of photo-oxidized heterocyclic rings were identified[56]
Sulfamethoxazole (SLF)Direct photolysis, hydroxylation, cleavage of the sulfonamide bond and fragmentation of the isoxazole
(ring
Very close to 100%Fast process, particularly under acidic pH. Indirect photolysis results in a decrease in degradation rate[57]
Tetracycline (TTR) Oxytetracycline (OXY) Chlortetracycline(CHL)Mainly indirect photolysis89.59% TTR
(100% OXY
(100% CHL
Effectiveness of the process is lower at higher initial concentrations for all three tetracyclines. Low concentrations of dissolved organic matter in these waters act as a photosensitizer. Higher toxicity of byproducts[58]
Trimethoprim (TRM) Sulfamethoxazole (SLF)Direct photolysis (48% for SLF, 18% for TRM)
(Indirect photolysis (52% for SLF, 82% for TRM)
~90% in both casesIndirect photolysis is attributable to the production of ·OH radicals and triplet excited state organic matter[59]
Table 5. Removal efficiency of antibiotics in waters by ozonation.
Table 5. Removal efficiency of antibiotics in waters by ozonation.
AntibioticMatrixOperation ConditionsMaximum Removal EfficiencyRemarksReference
Amoxicilin (AMX)Deionised water0.16 mM O3
(2.5 < pH < 7.2
~90%Fast process, low mineralization degree[63]
Amoxicilin (AMX)Formulation washwater57.5 mM O3
(3 < pH < 11.5
100%Complete removal after 40 min treatment at pH = 11.5[64]
Amoxicillin (AMX)
(Doxycycline (DXY)
(Ciprofloxacin (CPR)
(Sulphadiazine (SDZ)
Deionized water0.003–1.5 mM O3
(pH = 6.8
70% AMX
(92%–98% for DXY, CPR, and SDZ
Maximum removal achieved for 1.5 mM O3 [65]
Azithromycin (AZT)
(Clarithromycin (CLR)
(Roxithromycin (RXT)
Spiked WWTP
(effluent
0.01–0.1 mM O3
(pH = 7
~99%Excellent removal efficiencies above 0.042 mM O3[10]
Ciprofloxacin (CPR) Deionized water52 mM O3
(3 < pH < 10
95%O3 supply rather than reaction kinetics is rate limiting.
(Desethylene-CPR was identified as the major CPR degradation product
[66]
Ciprofloxacin (CPR)
(Erythromycin (ERY)
(Metronidazole (MTR)
(Trimethoprim (TRM)
Spiked STP effluent0.145 mM O3
(pH = 7
100% CPR
(94% ERY
(100% MTR
(94% TRM
Ozonation treatment was successfully used to improve conventional STP treatments[67]
Clarithromycin (CLR)
(Erythromycin (ERY)
(Roxithromycin (RXT)
Spiked STP
(effluent
0.1–0.3 mM O3
(pH = 7.2
76% (CLR)
(92% (ERY)
(91% (RXT)
(Below limit of quantification in all cases
Hydroxylated antibiotics should not further promote the formation of antibiotic-resistant strains[68]
Clarithromycin (CLR)Distilled water0.05 mM O3
(3.2 < pH < 4.4
100%High rate of reaction. Antibiotics fully eliminated even at a low ozone dose[69]
Flumequine (FLM)Ultrapure water140.6 mg O3 L−1 (in gas phase)
(3 < pH < 11
~100%Hydroxylation, decarboxylation and defluorination were mainly involved in the FLM ozonation.
(Removal efficiency increases with increasing pH
[70]
Lincomycin (LNC)Distilled water0.06–0.10 mM O3
(2 < pH <9
~100%Fast process, particularly at neutral pH[71]
Lincomycin (LNC)Distilled water0.4 mM O3
(5.5 < pH < 7.5
~100%Total removal achieved in 2 min[72]
Ofloxacin (OFX) Trimethoprim (TRM) Norfloxacin (NRF) Ciprofloxacin (CPR)Ultrapure water0.09 mM O3
(pH = 7
~100%All drugs completely removed within 10 s[73]
Oxytetracycline (OXY)Ultrapure water0.23 mM O3
(3 < pH < 7
100%Removal efficiency increases with increasing pH.
(Complete removal in 20 min
[74]
Roxithromycin (RXT)Spiked lake, river and well water0.002–0.042 mM O3
(pH = 8
>90%Remarkable influence of water matrix on ozone stability, formation of radicals and scavenging[75]
Spectinomycin (SPC)Distilled water0.06–0.10 mM O3
(2 < pH <9
~100%Fast process, particularly at neutral pH[71]
Sulfadiazine (SDZ)
(Sulfamethozaxole (SLF)
(Sulfapyridine (SLP)
(Sulfathiazole (STZ)
Spiked WWTP effluent0.01–0.1 mM O3
(pH = 7
99%Excellent removal efficiencies above 0.042 mM O3[10]
Sulfadiazine (SDZ)
(Sulfamethoxazole (SLF)
(Sulfathiazole (STZ)
(Sulfamethizole (SMT)
Deionized water0.02–0.067 mM O3
(2 < pH < 10
~100%Complete removal from contaminated water.
(Increasing the pH from 2.0 to 10.0 resulted in enhanced removal of the sulfonamides
[76]
Sulfamethoxazole (SLF)Spiked lake, river and well water0.002–0.042 mM O3
(pH = 8
>90%Remarkable influence of water matrix on ozone stability and formation of radicals.[75]
Sulfamethoxazole (SLF)Spiked STP
(effluent
0.1–0.3 mM O3
(pH = 7.2
92%
(Below limit of quantification
Hydroxylated antibiotics should not further promote the formation of antibiotic-resistant strains[68]
Sulfamethoxazole (SLF)Distilled water3.125–31.25 mM O3
(3 < pH < 11
100%Removal efficiency increases with increasing pH.
(Complete removal in 60 min, 31.25 mM O3
[77]
Sulfamethoxazole (SLF)
(Chlortetracycline (CHL)
Distilled waterO3 concentration not provided
(pH = 4.63 (SLF) or 4.33 (CHL)
~100%Total degradation achieved after 90 min.
(CHL was more quickly oxidized than SLF
[78]
Triclosan (TRC)Ultrapure water0.04 mM O3
(pH = 7
~100%2,4-dichlorophenol, chlorocatechol, mono-hydroxy-TRC, and dihydroxy-TRC were the main byproducts. Increasing O3 concentrations leads to decreased concentration of TRC and byproducts[79]
Trimethoprim (TRM)Spiked STP effluent0.1–0.3 mM O3
(pH = 7.2
85%Hydroxylated antibiotics should not further promote the formation of antibiotic resistant strains[68]
Table 6. Removal efficiency of antibiotics in waters by the O3/UV process.
Table 6. Removal efficiency of antibiotics in waters by the O3/UV process.
AntibioticMatrixOperation ConditionsMaximum Removal EfficiencyRemarksReference
Amoxicillin (AMX)Ultrapure waterO3 flow:16 mg·h−1
(T = 20 °C
(Low-pressure
(mercury vapor lamp (λ = 254 nm)
~100%Synergistic effect of direct ozonation, direct photolysis, and hydroxyl radical oxidation.
(·OH radicals generated in the photolysis of O3
[84]
Azithromycin (AZT)
(Norfloxacin (NRF)
(Ofloxacin (OFX) Roxithromycin (RXT)
Ultrapure water
(WWTP effluent
0.08 mM O3
(T = 20 °C
(Low-pressure
(mercury vapor lamp (λ = 254 nm)
≥98% (water)
(>87% (effluent)
Synergetic effect between O3 and
(UV irradiation
[85]
Azithromycin (AZT)
(Ciprofloxacin (CPR)
(Clarithromycin (CLR)
(Erythromycin (ERY)
(Levofloxacin (LVF)
(Lincomycin (LNC)
(Nalidixic acid (NLD)
(Roxithromycin (RXT)
(Sulfadimethoxine (SLM)
(Sulfamethoxazole (SLF)
(Trimethoprim (TRM)
WWTP effluentPilot-scale plant
(0.02–0.12 mM O3
(Room temperature
(Low-pressure
(mercury vapor lamp (λ = 254 nm)
CPR, SLM, LNC, NLD, SLF, LVF, ERY, and TRM below detection limit (LOD).
(CLR, AZT, and RXT insensitive or very stable in the O3/UV process
31 out of 38 PPCPs detected in the secondary effluent were degraded to or below their LOD[86]
Ciprofloxacin (CPR)
(Trimethoprim (TRM),
Ultrapure water2–20 mM O3
(Medium-pressure (MP) polychromatic
(UV lamp (λ=200–300 nm)
~100%O3-based
(processes more efficient than UV-based processes
[87]
Chloramphenicol (CHL)groundwater
(surface water
(WWTP effluent
Low-pressure
(mercury vapor lamp (λ = 254 nm)
(pH = 8.0–8.2
>90%Abatement efficiencies only moderately increased compared to conventional ozonation[88]
Sulfamethoxazole (SLF)Ultrapure water0.03 mM O3
(High-pressure
(mercury lamp (λ = 313 nm)
(Room temperature
~100%Complete removal achieved in 10 min[89]
Table 7. Removal efficiency of antibiotics in waters by the O3/H2O2 process.
Table 7. Removal efficiency of antibiotics in waters by the O3/H2O2 process.
AntibioticMatrixOperation ConditionsMaximum Removal EfficiencyRemarksReference
Amoxicillin (AMX)Ultrapure water
(Reservoir water
(Groundwater, Two secondary WWTP effluents
O3 flow: 16 mg·h−1
(H2O2= 10 μM
(T = 20 °C
~100% in all casesO3/H2O2 process leads to the highest rate constants.
(Degradation rate higher in the UP.
(Dissolved organic matter results in slower degradation process
[84]
Ciprofloxacin (CPR)Ultrapure waterO3 = 0.1 mM
(H2O2 = 2–990 μM
95% degradation reached after 60–75 minNo effect of temperature (6.0–62.0 °C).
(Low [H2O2] (2–50 μM) increased CPR degradation Large concentrations (990 μM) decreased degradation rates at pH 7
[91]
Ciprofloxacin (CPR)WWTP effluentO3 = 0.23 mM
(H2O2 = 20 mM
(0.15 mL H2O2 (30% w/v) injected every 5 min
>99% after 5 min
(>99.5% after 10 min
High degree of mineralization (>90%)[92]
Levofloxacin (LVF)Ultrapure waterO3 = 0.1 mM
(H2O2 = 2–100 μM
(pH = 3–10
95% (40 min) 99% (50 min)Strong influence of pH on levofloxacin degradation rate and reaction pathways
(H2O2 addition had only a limited effect
[66]
Metronidazole (MTR)WWTP effluentO3 = 0.23 mM
(H2O2 = 20 mM
(0.15 mL H2O2 (30% w/v) injected every 5 min
>92% after 5 minLow molecular weight carboxylates (mostly oxalates) as the final product[92]
Sulfamethoxazole
((SLF)
Ultrapure water
(Spiked WWTP effluent
O3 = 0.42 mM
(H2O2 = 5 mM
~100%Water matrix has no significant impact on SLF removal.
(Total degradation achieved in 45 min
[93]
Table 8. Removal efficiency of antibiotics in waters by the O3/H2O2/UV process.
Table 8. Removal efficiency of antibiotics in waters by the O3/H2O2/UV process.
AntibioticMatrixOperation ConditionsMaximum Removal EfficiencyRemarksReference
Berberine
((BRB)
Synthetic & real wastewater spiked with 1500 mg/L of BRBH2O2 = 0.5–4.0 mM
(Low-pressure mercury vapor lamp (λ = 254 nm)
(pH = 5–11
94.1%Performance of the process mainly relied on the H2O2 and O3 dosages, water alkalinity, and contact time[94]
Chlortetracycline (CHL)Livestock wastewaterO3 = 0.012 mM
(H2O2 = 0–5.9 mM
(Low-pressure mercury vapor lamp (λ = 254 nm)
(pH = 8.5
100% in less than 15 minComplete mineralization not achieved[95]
Ciprofloxacin (CPR)
(Trimethoprim (TRM)
2.5 mM phosphate buffer saline (PBS) at pH 7O3 = 0.1 mM
(H2O2 = 0.05–0.1 mM
(Medium-pressure (MP) polychromatic
(UV lamp (λ =200–300 nm)
>90%Larger contribution of O3-mediated degradation pathways (O3 for TRM and O3/H2O2 for CPR). UV contributes to a lesser extent[87]
Penicillin G (PNG)Ultrapure waterO3 = 0.03 mM
(H2O2 = 3 mM
(Low-pressure mercury vapor lamp (λ = 254 nm)
(
~80% in 30 minO3 alone was very effective
(A complete degradation or mineralization
(was not achieved
[96]
Sulfamethoxazole
((SLF)
Spiked ultrapure and tap waterO3 = 0.04 mM
(H2O2 = 1 mM
(Low-pressure mercury vapor lamp (λ = 254 nm)
(pH = 3–10
100%100% removal obtained in O3/UV system[97]
Table 9. Removal efficiency of antibiotics in waters by the H2O2/UV process.
Table 9. Removal efficiency of antibiotics in waters by the H2O2/UV process.
AntibioticMatrixOperation ConditionsMaximum Removal EfficiencyRemarksReference
Amoxicillin
((AMX)
Ultrapure waterH2O2 = 0.4–10 mM
(Low-pressure mercury lamp
((λ = 254 nm)
(pH = 2–10
99% in 20 minLow mineralization
(Antibacterial activity effectively eliminated
[107].
Cefalexin (CFL)
(Norfloxacin (NRF)
(Ofloxacin (OFX)
Ultrapure water and tap waterH2O2 = 0.25–5.0 mM
(Low-pressure mercury vapor lamp (λ = 254 nm)
~100% within 3–5 minScavenging effect if large concentrations of H2O2 are used
(Presence of halides in tap water accelerates the degradation rate
[108]
Ceftriaxone (CFN)Ultrapure water and tap waterH2O2 = 0.15–2.9 mM
(Low-pressure mercury vapor lamp (λ = 254 nm)
(pH = 5–9
~100%Optimum removal efficiency reached for [H2O2] = 0.3 mM
(Up to 35% synergistic effect achieved with respect to the photolysis process
(58.1% mineralization reached
[109]
Ciprofloxacin (CPR)
(Doxycycline (DXY)
(Oxytetracycline (OXY)
Ultrapure water
(
(Surface water
(
(Wastewater
H2O2 = 0.7–4.2 mM
(Low-pressure mercury lamp
((λ = 254 nm)
(pH = 2–10
100%Toxicity firstly increases, then decreases
(10% mineralization, total mineralization needed much more energy
[99]
Norfloxacin (NRF) H2O2 = 0.7–4.2 mM
(Low-pressure mercury lamp
((λ = 254 nm)
(pH = 2–10
100% in 100 minDirect photolysis infeasible (high reaction time and low mineralization)[110]
Ofloxacin (OFX)
(Sulfaquinoxaline(SLQ)
Ultrapure waterH2O2 = 0.8–9.0 mM
(Low-pressure mercury lamp
((λ = 254 nm)
>99% in 11 minOFX is degraded faster than SLQ
(Degradation products of OFX and SLQ are harmful to microorganisms
[111]
Roxithromycin (RXT)Ultrapure water
(Secondary wastewater effluent
H2O2 = 2–20 mM
(High-pressure
(mercury lamp (λ = 365 nm)
(pH = 4–9
~100% in appr 45 minSlightly alkaline favorable for the RXT degradation
(Degradation products more toxic than the parent compound
[112]
Sulfadiazine (SDZ)
(Sulfathiazole (STZ)
(Sulfamerazine (SMR)
(Sulfisoxazole (SSX)
(Sulfamethazine (SMZ)
(Sulfamethoxypyridazine (SMP)
(Sulfamonomethoxine (SMM)
(Sulfadimethoxypyrimidine (SDM)
Synthetic wastewater
(
(Hydrolyzed urine
(
(5 mM phosphate buffer (pH = 7)
H2O2 = 0.9 mM
(Low-pressure mercury lamp
((λ = 254 nm)
>99%Sulfonamides with five-membered heterocyclic group undergo rapid direct photolysis.[113]
Sulfamethazine (SMZ)Ultrapure waterH2O2 = 1–10 mM
(Low-pressure mercury lamp
((λ = 254 nm)
100% in 10 min57% mineralization in 120 min[114]
Sulfamethoxazole (SLF)Ultrapure waterH2O2 = 0, 0.15, and 0.30 mM
(Low-pressure and medium-pressure mercury lamps
((λ = 254 and 365 nm)
~100%Removal largely attributed to direct photodegradation
(Lower UV or H2O2 doses yielded different relative abundances of certain transformation products as compared to higher doses
[115]
Table 10. Removal efficiency of antibiotics in waters by the Fenton process.
Table 10. Removal efficiency of antibiotics in waters by the Fenton process.
AntibioticMatrixOperation ConditionsMaximum Removal EfficiencyRemarksReference
Amoxicillin (AMX)Spiked wastewaterH2O2 = 0.3–15 mM Fe2+ = 0–0.9 mM100% in 2.5 minBox-Behnken-statistical design 37% mineralization in 15 min[121]
Amoxicillin (AMX)Ultrapure waterH2O2 = 0.1–0.125 mM
(Fe2+ = 0.004–0.006 mM
(pH = 3.5 T = 20–30 °C
100% in 30 minCentral composite factorial design Only T and [Fe2+] affect statistically the removal efficiency[122]
Amoxicillin (AMX)Synthetic wastewaterH2O2 = 5–50 mM
(Fe2+ = 0.5–5 mM
(pH = 2–7
83% Optimum Fe2+/H2O2 molar ratio = 1/15 66% mineralization[123]
Ampicillin (AMP)Ultrapure waterH2O2 = 0.373 mM
(Fe2+ = 0.087 mM
(pH = 3.5
100% in 10 minCentral composite factorial experimental design
(Degradation products without antibacterial activity
[124]
Chlortetracycline (CHL)WastewaterH2O2 = 0.3 mM
(Fe2+ = 0.003–0.3 mM
(pH = 7
76%Complete mineralization not achieved[125]
Ciprofloxacin (CPR)Ultrapure waterH2O2 = 20–84 mM
(Fe2+ = 5–21 mM
(pH = 5
74% in 25 minOptimal conditions:
(H2O2 = 74.5 mM
(Fe2+ = 17.46 mM
(pH = 4.6
(Hydroxylation of both piperazine and quinolone rings; oxidation and cleavage of the piperazine ring, and defluorination (OH/F substitution) are the main degradation mechanisms
[126]
Ciprofloxacin (CPR)Ultrapure waterH2O2 = 26–51 mM
(Fe2+ = 5–10 mM
(pH = 3
76% in 45 minOptimal conditions:
(H2O2 = 26 mM
(Fe2+ = 5 mM
(pH = 3
(Complete mineralization could not be achieved
[127]
Ciprofloxacin (CPR)Spiked wastewaterH2O2 = 14.2 mM
(Fe2+ = 0.284–2.84 mM
(pH = 3
70% in 15 min55% mineralization achieved Considerable reduction in toxicity of the treated wastewater[128]
Doxycycline (DXY)Ultrapure waterH2O2 = 2.9–26.5 mM
(Fe2+ = 0.09–2.1 mM
(T = 0–40 °C
(pH = 5
100% in 10 minOptimal conditions:
(H2O2 = 18 mM
(Fe2+ = 0.44 mM
(T = 35 °C
[129]
Flumequine (FLM)Ultrapure waterH2O2 = 0.5–10 mM
(Fe2+ = 0.25–1 mM
(pH = 2.8
40% in 15 minLow mineralization degree
(Deactivation of antimicrobial activity
[130]
Levofloxacine (LVF)Ultrapure waterH2O2 = 0.375–1.5 mM Fe2+ = 0.0375–0.15 mM pH = 3 100% Total removal achieved within 5–90 min according to experimental conditions
(Defluorination, piperazinyl substituent transformation, and quinolone moiety modifications are the main degradation pathways
[131]
Sulfamethoxazole (SLF)Ultrapure water Synthetic wastewaterH2O2 = 0.5–4 mM
(Fe2+ = 0.025–0.2 mM
(pH = 3
100% in 10 min (ultrapure water) 53% in 30 min (synthetic wastewater)Wastewater components had a negative effect on sulfamethoxazole degradation
(Degradation pathways:
((a) Oxidation of –NH2 in benzene ring by ·OH radicals followed by hydroxylation
((b) -SH-Ph bond cleavage
[132]
Trimethoprim (TRM)Ultrapure water Synthetic wastewaterH2O2 = 0.5–4 mM
(Fe2+ = 0.025–0.2 mM
(pH = 3
100% in ultrapure water 36% in synthetic wastewaterHydroxylation is the first degradation step, followed by the cleavage of the C-C bond between the pyrimidine and the benzene rings[133]
Table 11. Removal efficiency of antibiotics in waters through heterogeneous Fenton-like process.
Table 11. Removal efficiency of antibiotics in waters through heterogeneous Fenton-like process.
AntibioticMatrixOperation ConditionsMaximum Removal EfficiencyRemarksReference
Amoxicilin (AMX)Ultrapure waterH2O2 = 3.3–12.2 mM
(nZVI = 0.5–2.0 g/L
(pH = 2.0–5.0
(T = 15–45 °C
~90% in 20 min(a)Optimal conditions:
(H2O2 = 6.6 mM, nZVI = 0.5 g/L pH = 3.0
(T = 30 °C
(Adsorption of AMX onto nZVI or its (hydr)oxide surface plays an important role
[143]
Ciprofloxacin (CPR)Ultrapure waterH2O2 = 100 mM nZVI = 0.056–0.28 g/L
(pH = 7
(Room temperature
100% in 30 min(a)Reaction at the piperazinyl ring and defluorination followed by hydroxyl substitution appear to be the main degradation pathways[144]
Ciprofloxacin (CPR)Ultrapure waterH2O2 = 10 mM
(Catalysts (0.5 g/L):
(MnCuO2 FeCuO2
(CoCuO2
(NiCuO2
(pH = 6
~90%(b)CPR degradation mainly occurs in solution. Scarce contribution of adsorption
(Degradation of CPR should be due to the cleavage of piperazine ring, followed by loss of formaldehyde, replacement of F with OH and/or loss of ethylamine
[140]
Ciprofloxacin (CPR)Ultrapure waterH2O2 = 10–100 mM
(Sludge Biochar Catalyst (SBC) = 0.2 g/L
(pH = 2–12
90% in 4 h(c)Fe2+ and Fe3+ were released in the SBC/H2O2 system
(Piperazine ring cleavage, pyridine cleavage, hydroxylation, F/OH substitution, and defluorination were the dominant degradation pathways
[145]
Metronidazol
((MTR)
Ultrapure waternZVI = 0.03–0.13 g L−1
(pH = 3.03–9.04
96.4% in 5 min(a)H2O2 generated according to Reaction (51)[146]
Metronidazole (MTR)Ultrapure waterAbsence of Fe and H2O2
(
(Addition of 2 mM H2O2 in one experiment
92%(d)Three-dimensional macroporous graphene-wrapped zero-valent copper nanoparticles (3D-GN@Cu0) used as the catalyst
(
(H2O2 generated in situ by reduction of O2 on the surface of 3D-GN@Cu0
(Addition of 2 mM H2O2 had little effect on the degradation of MTR
[142]
Tetracycline (TTR)Ultrapure waterH2O2 = 100 mM Fe0@CeO2 catalyst = 0.1 g/L pH = 5.8 T = 26 °C94%(b)A combined adsorption/reduction mechanism enhances removal efficiency[136]
Tetracycline (TTR)Ultrapure waterH2O2 = 3–20 mM
(Fe(III) concentration not specified
(WMoOx catalyst = 0.2–1.6 g/L
(pH = 3–8
(T = 25 °C
86%(b)The system avoids solution chroma and sludge formation caused by the dissolved ferric species[139]
Tetracycline (TTR)Ultrapure water
(
(Spiked wastewater
H2O2 = 5 mM
(pH = 7.4
(T = 25 °C
(Fe substituted by a mixture of three biochars from corn stalks, bamboo, and pig manure
100%(c)Pig manure showed the best performance in TTR removal[147]
Tetracycline (TTR)Ultrapure waterH2O2 = 1.1–3.3 mM
(
(α-FeOOH/RGO hydrogels used as catalysts
100% in 120 min(d)α-FeOOH/RGO hydrogels could generate reactive oxygen species (ROS)
(without the addition of H2O2
(TTR acts as an electron donor.
(e are transferred through π–π interactions (TTR -graphene) and π–Fe interactions
((graphene- FeOOH)
[148]
KEY: Catalysts used: (a)nZVI; (b)MOx; (c)Biochars; (d)Graphene/graphene oxide.
Table 12. Removal efficiency of antibiotics in waters by photo-Fenton processes.
Table 12. Removal efficiency of antibiotics in waters by photo-Fenton processes.
AntibioticMatrixOperation ConditionsMaximum Removal EfficiencyRemarksReference
Amoxicillin (AMX)Spiked synthetic wastewater
(Spiked real wastewater
H2O2 = 0.08 mM
(Fe3+ = 0.05 mM
(Natural solar radiation (pilot-plant scale CPC photoreactor)
(pH = 7–8
90% in 9 minNo mineralization of the drug.
(Hydroxylation of the aromatic ring, opening of the β-lactam ring, and subsequent formation of amoxilloic and amoxicilloic acids are the main transformation pathways.
[152]
Ampicillin (AMP)Spiked WWTP effluentSolar photo-Fenton
(H2O2 = 0.74–2.94 mM
(Fe2+ = 0.09 mM
(pH = 3
100% in 20 minOptimal conditions:
(H2O2 = 2.2 mM
(Fe2+ = 0.09 mM
(Beyond the optimal H2O2 concentration, scavenging effects might occur
[153]
Chloramphenicol
((CHL)
Spiked WWTP effluentH2O2 = 0.044–0.088 mM
(Fe2+ = 0.016–0.064 mM
(Black light lamps (λ = 350–400 nm) or solar irradiation
(pH = 5.8–7.7
79% in 20 minOptimal conditions:
(H2O2 = 0.088 mM
(Fe2+ = 0.048 mM
(pH = 5.8
(Acidification and neutralization before the discharge are avoided
[154]
Ciprofloxacin (CPR)Ultrapure waterH2O2 = 5–25 mM
(High-pressure
(mercury lamp (λ = 362 nm)
(T = 25 °C
(Fe2+ = 0.25–2 mM
(pH = 2–9
93% in 45 minOptimal conditions:
(H2O2 = 10 mM
(Fe2+ = 1.25 mM
(pH = 3.5
(70% mineralization reached
(Piperazine ring degradation is the main degradation pathway
[155]
Oxacillin (OXC)Ultrapure waterH2O2 = 0.09–10 mM
(Fe2+ = 0.0036–0.09 mM
(High-pressure
(mercury lamp (λ = 365 nm)
(pH = 6
(T = 25 °C
100% in 20 minOptimal conditions
(H2O2 = 10 mM
(Fe2+ = 0.09 mM
(Light intensity = 30 W
(Effluent has no antimicrobial activity
(Near-neutral conditions are used
[156]
Trimethoprim (TRM)Ultrapure waterH2O2 = 0.03–5 mM
(High-pressure
(mercury lamp (λ = 360 nm)
(T = 25 °C
(Fe2+ = 0.03–2 mM
(pH = 2.5–4.5
99.5% in 6 minOptimal conditions:
(H2O2 = 0.09 mM
(Fe2+ = 0.09 mM
(pH = 4.56
[157]
Table 13. Removal efficiency of antibiotics in waters by TiO2/UV advanced oxidation processes.
Table 13. Removal efficiency of antibiotics in waters by TiO2/UV advanced oxidation processes.
AntibioticMatrixOperation ConditionsMaximum Removal EfficiencyRemarksReference
Ciprofloxacin
((CPR)
Ultrapure waterGraphitized mesoporous carbon (GMC)-TiO2 nanocomposite used as a catalyst (0.35 g/L)
(Low-pressure UV lamp (λ = 254 nm)
100% in 45 minTotal mineralization achieved in 90 min
(
(Hydroxylation, cleavage of piperazine ring and decarboxylation are the main degradation pathways
[170]
Cloxacillin
((CLX)
Ultrapure water;
(
(Synthetic pharmaceutical wastewater
TiO2 = 2.0 g/L; UV light = 150 W~100%TiO2 photocatalysis exhibits larger degradation and mineralization efficiencies than other systems also tested[171]
Metronidazole
((MTR)
Complex aqueous matrix
((contains anions, cations, humic acid, and glucose)
TiO2 = 1.5 g/L
(UV light intensity = 6.5 mW cm−2
~88% in max 30 minThe presence of common water matrix components hinders drug degradation (except glucose)[172]
Norfloxacin
((NRF)
Ultrapure waterTiO2 = 0.3 g/L
(Low-pressure UV lamp (λ = 254 nm)
~90%TiO2 photocatalysis is the second most effective method for the removal of NRF, after photo-Fenton (96%)[173]
Oxacillin
((OXC)
Ultrapure waterTiO2 = 0.5 g/L
(High-pressure
(mercury lamp (λ = 365 nm)
(UV = 150 W
100% in 45 min∼90% mineralization achieved in 135 min[156]
Oxacillin
((OXC)
Synthetic pharmaceutical effluentTiO2 = 0.5 g/L
(High-pressure
(mercury lamp (λ = 365 nm)
(UV = 150 W
100% in 45 min (without additives)
(100% in 60 min (with additives)
TiO2 photocatalytic treatment was the least inhibited by additives[174]

Share and Cite

MDPI and ACS Style

Cuerda-Correa, E.M.; Alexandre-Franco, M.F.; Fernández-González, C. Advanced Oxidation Processes for the Removal of Antibiotics from Water. An Overview. Water 2020, 12, 102. https://doi.org/10.3390/w12010102

AMA Style

Cuerda-Correa EM, Alexandre-Franco MF, Fernández-González C. Advanced Oxidation Processes for the Removal of Antibiotics from Water. An Overview. Water. 2020; 12(1):102. https://doi.org/10.3390/w12010102

Chicago/Turabian Style

Cuerda-Correa, Eduardo Manuel, María F. Alexandre-Franco, and Carmen Fernández-González. 2020. "Advanced Oxidation Processes for the Removal of Antibiotics from Water. An Overview" Water 12, no. 1: 102. https://doi.org/10.3390/w12010102

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop